INSTRUCTIONS FOR BLOWER INSTALLATION
NOTE: Set up as close to power source as possible. The product
should be periodically examined for potentially unsafe conditions
such as: damaged cord, plug, housing or parts, and that in the
event such damage is found, the product should not be used until
properly repaired. Never leave the blower outside in the rain or
exposed to the elements when not in use. When in use, do not
place the cord across traffic areas, water or damp areas. The
blower should be placed on a stable surface and anchored per
product instructions. The power cord of the blower is equipped
with a Ground Faulty Current Interrupter (GFCI) plug.
1) Make sure that the blower switch is in the “OFF” position. Plug
the blower into a properly grounded 110-120V GFCI outlet.
2) If the GFCI has been tripped, press the “RESET” button to
restore power to the blower.
3) Set the power switch of the blower to “ON” to inflate. After use,
turn the power to “OFF”.
4) To disconnect, have an adult grip it tightly and pull the plug
from wall outlet.
WARNING: Failure to follow these instructions
could result in serious injury or death.
• ADULT SET-UP AND SUPERVISION REQUIRED.
• Use only with Ground Fault Circuit Interrupt (GFCI) receptacle.
• This blower is for residential use only. It is not intended to be
used in commercial or industrial settings.
• Never insert fingers, pencils or any other object through the grill
at ANY time.
•Do not operate blower with a damaged cord or plug, after the appliance
malfunctions or has been dropped or damaged in any manner.
• Do not operate in the presence of explosive and/or flammable
fumes.
• Never connect the blower to any solid - state speed control
device.
• To reduce the risk of fire or electric shock, do not use this blower
with any solid-state speed control device.
• WARNING – Electronic hazard – Do not use extension cords with
this product.
• Always unplug the blower before servicing.
• Outdoor use only.
CAUTION: ELECTRICALLY
OPERATED PRODUCT
DANGER - TO PREVENT ELECTRIC SHOCK, DO NOT IMMERSE
IN WATER. WIPE CLEAN WITH DAMP CLOTH.
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH. ADULT SET-
UP AND SUPERVISION REQUIRED.
MODEL W-1.5L
BLOWER SPECIFICATIONS: 115V (AC),
60 Hz, 3.2A, 368W
USE ONLY ON GFCI PROTECTED RECEPTACLES CAUTION
GROUNDING INSTRUCTIONS FOR ALL GROUNDED, CORD-CONNECTED PRODUCTS
This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an ap-
propriate grounding plug. This plug must be plugged into an outlet that is properly installed and grounded in accordance with
all local codes and ordinances. DANGER - Improper installation of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The
wire with insulation having an outer surface that is green, with or without yellow stripes, is the grounding wire. Check with a
qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether
the product is properly grounded. Do not modify the plug provided; if it will not fit the outlet, have the proper outlet installed
by a qualified electrician. For a grounded, cord-connected product, rated less than 15 amperes and intended for use on a
nominal 110-120-volt supply circuit, these instructions should be followed. This product is for use on a nominal 110-120-
volt supply circuit, and has a grounding plug that looks like the plug illustrated in sketch A. Temporary adapters should not
be used. Do not use product until a properly grounded outlet (sketch A) can be installed by a qualified electrician.
INSTRUCTIONS FOR BLOWER CLEANING AND STORAGE
Do not immerse the blower in water. Unplug the blower before cleaning. To clean: wipe with a damp cloth. The blower does not require
any lubrication and has no user serviceable parts. Do not attempt to service the blower. When not in use, store the blower indoors in a
dry place. Store the blower upright on a stable surface. Loosely coil the cord and place it beside the blower.
• Blowermust be unplugged before servicing.
• Product should be periodically examined for potentially unsafe
conditions such as damaged cord, plug, housing, or parts, and that
in the even such damage is found, the product should not be used
until properly repaired. If these checks are not carried out, the toy
could overturn or otherwise become a hazard.
• The blower does not require any lubrication and has no user
serviceable parts. Do not attempt to service the blower.
• Do not immerse the fan in water. To clean, wipe with a damp cloth.
• Regularly check the intake and output openings and keep free of
dirt, leaves, etc.
• When not in use, store the blower indoors in a dry place.
• Store the blower upright on a stable surface.
• Loosely coil the cord and place it beside the blower.
• When in use, do not place the cord across traffic areas, water or
damp areas.
• The blower is a high volume blower, and is capable of moving large
volumes of air very quickly. Place the blower in an area where it will
not draw in dirt or leaves.
2
Repair Kit Instructions
WARNING: Repair patches must be applied by an adult only. KEEP OUT OF REACH OF CHILDREN.
REPAIR PATCH INSTRUCTION
1. Deflate the item, clean the area and allow to dry thoroughly.
2. Cut a portion of the patch to the size needed and round the corners. (See Fig. 1 & 2).
3. Remove the adhesive backing from the patch material, position the patch over the damaged area and smooth out any bubbles.
4. Allow to sit for 30 minutes before re-inflating.
WARNING: NOT A TOY. ADULT USE ONLY.
Repair kit. Keep away from children.
1
Instructions for
Bouncer Maintenance
Instructions for
Blower Maintenance
• As an outdoor product, the bouncer is subject to wear and
deterioration. Inspect for signs of fabric failure; weak or torn
surfaces must be repaired promptly.
• To keep the product clean: wipe the bouncer or blower using a dry
cloth or a cloth dampened with a neutral, non-inflammable non-
toxic cleaning and sanitizing solution or pure water.
• Product should never be stored wet. Allow to dry before rolling up.
Disposal
• Disassemble and dispose of the equipment in such a manner
that no hazardous conditions exist at the time the equipment is
discarded.
• Blower should be returned to a collection center capable of
processing electrical/electronic waste.
