430435

Linksys wireless g adsl gateway wag54g Manual

34
Zoom out
Zoom in
Previous page
1/99
Next page
27
Chapter 5: Configuring the Gateway
The Wireless Tab
Wireless-G ADSL Gateway
Advanced Wireless Settings Tab
Advanced Wireless
On this screen you can access the Advanced Wireless features, including Authentication Type, Basic Data Rates,
Control Tx Rates, Beacon Interval, DTIM Interval, RTS Threshold, and Fragmentation Threshold.
• Authentication Type. The default is set to Auto (default), which allows either Open System or Shared Key
authentication to be used. For Open System authentication, the sender and the recipient do not use a WEP
key for authentication but can use WEP for data encryption. If you want to allow on Open System
authentication, then select Open System. For Shared Key authentication, the sender and recipient use a WEP
key for both authentication and data encryption. If you want to use only Shared Key authentication, then
select Shared Key. It is recommended that this option be left in the default (Auto) mode, because some
clients cannot be configured for Shared Key.
• Control Tx Rates. The default transmission rate is Auto. The range is from 1 to 54Mbps. The rate of data
transmission should be set depending on the speed of your wireless network. You can select from a range of
transmission speeds, or keep the default setting, Auto, to have the Gateway automatically use the fastest
possible data rate and enable the Auto-Fallback feature. Auto-Fallback will negotiate the best possible
connection speed between the Gateway and a wireless client.
• Beacon Interval. The default value is 100. Enter a value between 1 and 65,535 milliseconds. The Beacon
Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Gateway
to synchronize the wireless network.
• DTIM Interval. The default value is 3. This value, between 1 and 255, indicates the interval of the Delivery
Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for
listening to broadcast and multicast messages. When the Gateway has buffered broadcast or multicast
messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients hear the
beacons and awaken to receive the broadcast and multicast messages.
• Fragmentation Threshold. This value should remain at its default setting of 2346. The range is 256-2346
bytes. It specifies the maximum size for a packet before data is fragmented into multiple packets. If you
experience a high packet error rate, you may slightly increase the Fragmentation Threshold. Setting the
Fragmentation Threshold too low may result in poor network performance. Only minor modifications of this
value are recommended.
• RTS Threshold. This value should remain at its default setting of 2347. The range is 0-2347 bytes. If you
encounter inconsistent data flow, only minor modifications are recommended. If a network packet is smaller
than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Gateway sends Request
to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After
Figure 5-20: Advanced Wireless Settings
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Linksys wireless g adsl gateway wag54g at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Linksys wireless g adsl gateway wag54g in the language / languages: English as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info