430435

Linksys wireless g adsl gateway wag54g Manual

18
Zoom out
Zoom in
Previous page
1/99
Next page
11
Chapter 4: Connecting the Wireless-G ADSL Gateway
Wired Connection to a Computer
Wireless-G ADSL Gateway
Wired Connection to a Computer
1. Before you begin, make sure that all of your network’s hardware is powered off, including the Gateway and
all computers.
2. Connect one end of an Ethernet network cable to one of the Ethernet ports (labeled 1-4) on the back of the
Gateway (see Figure 4-1), and the other end to an Ethernet port on a computer.
3. Repeat this step to connect more computers, a switch, or other network devices to the Gateway.
4. Connect a phone cable from the Line port on the Gateway’s back panel (see Figure 4-2) to the wall jack of the
ADSL line. A small device called a microfilter may be necessary between each phone and wall jack to prevent
interference. Contact your ISP if you have any questions.
5. Connect the power adapter to the Gateway’s Power port (see Figure 4-3), and then plug the power adapter
into a power outlet. Turn the On/Off switch to On.
• The Power LED on the front panel will light up green as soon as the power adapter is connected properly
and the switch is turned on. The Power LED will flash for a few seconds, then it will light up steady when
the self-test is complete. If the LED flashes for one minute or longer, see “Appendix A: Troubleshooting.”
6. Power on one of your computers that is connected to the Gateway.
Figure 4-2: ADSL Connection
Figure 4-1: Ethernet Connection
Figure 4-3: Power Connection
NOTE: You should always plug the Gateway’s power
adapter into a power strip with surge protection.
IMPORTANT: For countries that have phone jacks with RJ-11 connectors, make sure to
only place the microfilters between the phone and the wall jack and not between the
Modem and the wall jack or your ADSL will not connect.
For countries that do not have phone jacks with RJ-11 connectors (e.g. France, Sweden,
Switzerland, United Kingdom, etc.), except for ISDN users, the microfilter has to be used
between the modem and the wall jack, because the microfilter will have the RJ-11
connector.
Annex B users (E1 and DE versions of the Gateway) must use the included special cable to
connect the gateway to the wall jack (RJ-45 to RJ-12). If you require splitters or special
jacks, please contact your service provider.
NOTE:
A small device called a microfilter (not included) may be necessary between each
phone and wall jack to prevent interference. Contact your ISP if you have any questions.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Linksys wireless g adsl gateway wag54g at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Linksys wireless g adsl gateway wag54g in the language / languages: English as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info