495209
7
Zoom out
Zoom in
Previous page
1/39
Next page
Chapter 3
Installation
6
Wireless-G ADSL Home Gateway
Chapter 3: Installation
Linksys strongly recommends that you run the Setup CD-
ROM. If you have problems running the Setup CD-ROM,
use this chapter.
Connection
Make sure that all the devices that you are working
with are powered down, including your computer(s)
and the Gateway. If you have a modem connected
to your network, disconnect it. The Gateway replaces
your modem.
Connect one end of the provided Ethernet cable to
your computer’s Ethernet adapter. Connect the other
end of the Ethernet cable to one of the Ethernet ports
on the back of the Gateway.
Connect the Computer
Repeat step 2 for every computer or device that you
want to connect to the Gateway via Ethernet. If you
connect more than four computers to the Gateway,
you also need to connect a switch to the Gateway.
NOTE: If your computer’s Ethernet adapter
is not set up, refer to the Ethernet adapter’s
documentation for more information.
Connect one end of the phone cable to the DSL port
on the back of the Gateway.
Connect the other end of the phone cable to the wall
jack with ADSL service or microfilter.
Connect the DSL
1.
2.
3.
5.
4.
NOTE: To avoid interference, you may need to
place a microfilter or splitter between the phone
cable and wall jack. Contact your ISP to determine
if one is required. (UK residents need to connect
the microfilter to the wall phone jack with ADSL
service and then connect one end of the provided
phone cable to the DSL port on it.) If you have
more than one phone and you experience static
on the line after installing the Gateway, then you
need to install an additional microfilter for each
phone or fax that you use. If you use ISDN, then
you do not need a microfilter.
Connect the power adapter to the Gateway’s power
port and the electrical outlet.
Connect the Power
Power on the computer that you want to use to
configure the Gateway.
The Power, Wireless, and at least one of the numbered
Ethernet (1, 2, 3, or 4) LEDs should light up. If not, make
sure the Gateway is powered on and the cables are
securely connected.
Connection is complete.
Continue to the “Setup” section.
Setup
For setup, configure the Gateway to access the Internet
through your ADSL Internet Service Provider (ISP). Use the
setup information provided by your ISP.
Continue to Chapter 4: Advanced Configuration, and
complete the following sections:
Setup > Basic Setup
Wireless > Basic Wireless Settings
Wireless > Wireless Security
After completing the setup, test the Gateway. Enter
www.linksys.com/uk/registration in the web browser’s
Address field, and press Enter.
Installation is complete.
6.
7.
8.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Linksys WAG200G - Wireless-G ADSL Home Gateway at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Linksys WAG200G - Wireless-G ADSL Home Gateway in the language / languages: English as an attachment in your email.

The manual is 3,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info