602203

Linksys BEFSR41 Ver. 2 Manual

9
Zoom out
Zoom in
Previous page
1/66
Next page
EtherFast
®
Cable/DSL Routers
11
Instant Broadband
™
Series
10
Chapter 3: Getting to Know the 1-
Port EtherFast Cable/DSL Router
The rear panel of the Router is where all of the Router’s cabling connections
are made, and where you can reset or configure the Router’s LAN port, as
shown in Figure 3-1.
WA N The WA N (Wide Area Network) port is where you
connect your cable or DSL modem through an
Ethernet cable. Your modem connection will not
work from any other port.
LAN The LAN (Local Area Network) port is where you
connect the Router to a PC, hub, or switch. If you
have more than one PC, connect an Ethernet hub or
switch to the Router, and then connect your PCs to
that hub or switch.
Power The Power port is where you will connect the
power adapter.
Buttons & Switches
The Reset Button Details on the Reset button are found in the
“Chapter 2: Getting to Know the 4-Port EtherFast
Cable/DSL Router.”
The 1-Port Router’s Rear Panel
Figure 3-1
The WAN Indicators
Link Green. The Link LED lights up when a successful connec-
tion is made between the Router and your cable or DSL
modem or network.
Act Green. The Act LED flickers when the Router is sending or
receiving data over the WA N port (to the Internet).
Diag Red. The Diag LED lights up when the Router goes through
its self-diagnosis mode during every boot-up. It will turn off
upon successful completion of the diagnosis.
If this LED stays on for an abnormally long period of time,
see “Appendix A: Troubleshooting.”
Proceed to “Chapter 5: Connect the Router.”
The Reset Button
*
The Reset button can be used in one of two ways.
1. If the Router is having problems connecting to the Internet, press the Reset
button for just a moment with a paper clip or a pencil tip. This clears up any
jammed connections, and is similar to pressing the Reset button on your PC
to reboot it.
2. If you are experiencing extreme problems with the Router and have tried all
other troubleshooting measures, press the Reset Button and hold it down
until the red Diag LED on the front panel turns on and off completely.
This will restore factory defaults and clear all of the Router’s settings, includ-
ing settings such as IP addresses or a new password.
* The Reset Button is located on the front panel of the 4-Port Router, and the rear panels of the 3-
Port Router and the 1-Port Router.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Linksys BEFSR41 Ver. 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Linksys BEFSR41 Ver. 2 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info