697398

LightPro LED Strip Connector 176L Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
LED Strip and Connector
User manual
Thank you for buying the Lightpro LED Strip and
Connector. This document contains the required
information for correct, efcient, and safe use of the
product. Consult the general manual of the Lightpro
12-volt system and the user manual of your Lightpro
transformer for more information about the set up and
connection of your light plan.
Read the information in this manual carefully before
using the product. Keep this manual near the product
for consultation in the future.
PRODUCT DESCRIPTION
The Lightpro LED Strip is a lighting chain for outdoor
use. The strip can be cut to the desired length before
installation. Attention: before cutting, read the instruc-
tions in this manual carefully!
This product can be used as outdoor lighting in com-
bination with the Lightpro 12 Volt system. Improper
use of the product can have consequences for the
safety, warranty, and correct functioning of the product
and/or other parts of the system.
Specications LED Strip
Article number 175L
Power (per meter) 2,2W
Luminous ux (per meter) 80-100lm
Protection class IP67
Ambient temperature -20°C to 50°C
Dimmable No
Specications LED Strip Connector
Article number 176L
Maximum Power 36W
Afmetingen (l x b x h) 1m x 28mm x 28mm
Protection class IP44
Ambient temperature -20°C to 50°C
Cable length 1m
USE
Packaging content
[Figure A]
1. LED Strip Connector
2. Sealing rubber
3. End cap
Check if all parts are present in the packaging. For
questions about parts, service, and any complaints or
other remarks, you can always contact us.
E-mail: info@lightpro.nl
Available separately
[Figure B]
1. LED Strip (Article number 175L)
2. Lightpro connector (Article number 137A)
CUTTING
[Figure C]
The LED Strip can be cut to any desired length. Cut
through in one movement from the transparent side.
Carefully follow these instructions when cutting the
strip:
1. The LED Strip has been marked with the print DO
NOT CUT HERE. Never cut in this part of the strip.
2. The strip can be shortened as desired. The part of
the strip that is connected to the connector has to
have at least one marking.
3. Short (remaining) parts of the LED Strip which do
not have a marking will not light when connected to
the connector.
4. It is possible that a small part of a few centimetres at
the end of the strip will not light up after cutting.
ASSEMBLE
[Figure D]
1. Unscrew the screw cap and move it to the back.
The LED Strip has to be connected in the right
direction to the connector. When connecting, pay
attention to the direction of the arrow with the print
CONNECTOR. The arrow points in the direction of the
connector.
2. Place the sealing rubber at around 5 cm on the LED
Strip.
3. Connect the LED Strip to the Connector. Make sure
the pins in the connector make proper contact with
the conductors in the strip.
4. Press the sealing rubber to the connector.
5. Place the screw cap on the connector and tighten
properly.
6. Place the end cap at the end of the LED Strip.
GB
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LightPro LED Strip Connector 176L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LightPro LED Strip Connector 176L in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info