697328

LightPro Castor 3 - 177S Manual

7
Zoom out
Zoom in
Previous page
1/12
Next page
Castor 3
User manual
Thank you for purchasing the Lightpro Castor 3.
This document contains the required information for
correct, efcient, and safe use of the product. Consult
the general manual of the Lightpro 12-volt system
and the user manual of your transformer for more
information about the set up and connection of your
light plan.
Read the information in this manual carefully before
using the product. Keep this manual near the product
for consultation in the future.
PRODUCT DESCRIPTION
The Lightpro Castor 3 is an LED spot for outdoor use.
The xture can be installed on a xed underground
with the included screws, or be placed in the ground
with the included spike. This product may only be
used as outdoor lighting in combination with the
Lightpro 12-volt system. Any alterations made to
the product may have consequences for the safety,
warranty, and correct functioning of the product and/
or other parts of the system.
Specications
Product Lightpro Castor 3
Article number 177S
Power (max.) 2.5W
Luminous ux 200 lm
Dimensions (H x W x D) 120 x 60 x 100 mm
Protection class IP44
Ambient temperature -20°C to 50°C
Cable length 1m
Dimmable No
INSTALLATION
Packaging content
[Figure A]
1. Fixture Castor 3
2. Ground spike
3. Screw
4. Plug
5. Lightpro connector
6. Hex key (large)
7. Hex key (small)
Check if all parts are present in the packaging. For
questions about parts, service, and any complaints or
other remarks, you can always contact us.
E-mail: info@lightpro.nl
Option 1: placement on a xed underground or
mounting to a wall
[Figure B]
1. Remove the screw from the base using the included
large hex key (Figure A [6]).
2. Remove the xture from the base.
[Figure C]
• Install the base onto the underground with the
included screw.
If necessary, drill a hole in the underground and use
the included plug.
[Figure D]
1. Place the xture in the base.
2. Place the screw in the base.
3. Put the xture in the desired position.
4. Fasten the screw using the included large hex key
(Figure A [6]).
Option 2: placement in the ground
[Figure E]
1. Place the spike underneath the base.
2. Properly fasten the spike.
3. Put the xture in the desired position.
4. Fasten the screw using the included large hex key
(Figure A [6]).
5. Place the xture in the ground.
GB
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LightPro Castor 3 - 177S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LightPro Castor 3 - 177S in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info