697326
9
Zoom out
Zoom in
Previous page
1/12
Next page
GB
Read the safety instructions carefully and follow the advice. Keep these instructions in case you need them
later.
The product you just have bought complies to all european and national qualications with respect to the
specied LVD (Low Voltage Directive) and Electro Magnetic Compatibilty (EMC) (89/336/EEG)
SAFETY
Do not use this product in areas where combustible gases, fumes or liquids may be stored. Install the
product a safe distance away from highly ammable materials.
Always t this product so that it can still be accessed for servicing or maintenance. This product must never
be permanently embedded or bricked in.
This product is suitable for outdoor use (IP44/IP67, splash-water-proof).
This product is suitable for outside temperatures of: -20
o
C till 50
o
C.
If the protective glass is broken, it must be replaced before the product is used again!
The distance away from the surfaces to be illuminated by the product must be a minimum of 0.5 m.
Protection class III: this product may only be connected to safety extra-low voltage up to a maximum of 12
Volts.
Use the correct type of light source and ensure that the maximum wattage is not exceeded. The correct light
source is indicated on the (label of the) bracket by a symbol and is the maximum wattage shown.
INSTALLATION OF THE LIGHTS
1. Install the products in the desired position and lay the cables so that they can be comfortably connected
to the transformer or cables.
2. If products are provided with a drain hole for water, this hole must be pointing downwards.
3. Use non-corrosive xing materials (supplied as standard) if you want to bolt the products down.
4. Connect the lights to the main cable by using the connector as shown on page 5.
5. Plug the plug of the transformer into the wall socket (230 Volt 50 Hz).
REPLACEABLE LIGHTSOURCE
Proceed as follows in order to install or change the light source:
1. Turn the power off.
2. Let the light source cool down for at least 5 minutes.
3. Replace the light source, bearing the following points in mind:
• Only replace the light source by an identical model with the same specications.
• When (re)assembling, ensure that the parts are dry and clean.
4. Turn the power back on.
MANUAL AND
SAFETY INSTRUCTIONS
8 9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LightPro Barite 40 - 112P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LightPro Barite 40 - 112P in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of LightPro Barite 40 - 112P

LightPro Barite 40 - 112P Additional guide - Dutch - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info