600894

Liftmaster 8587 Elite Manual

48
Zoom out
Zoom in
Previous page
1/76
Next page
10
Pour éviter d’éventuelles BLESSURES GRAVES par
suite de la chute d’un ouvre-porte de garage, fixer
l’ouvre-porte SOLIDEMENT aux solives du garage. On
DOIT utiliser des ancrages de béton si les supports sont
posés dans la maçonnerie.
MATÉRIEL
Boulon hexagonal de
5/16 po-18 x 7/8 po
Écrou de 5/16 po-18
Rondelle frein
de 5/16 po
La suspension de l'ouvre-porte de garage variera en
fonction de votre garage. Les illustrations représentent
deux poses types. La pose peut toutefois être différente.
Les supports de suspension doivent être inclinés
(Figure 1) pour assurer un support rigide. Dans le cas
d’un plafond fini (Figure 2), fixer une cornière aux
solives du plafond avant de poser l’ouvre-porte. La
cornière et les fixations ne sont pas fournies.
Les instructions ci-dessous indiquent comment attacher
votre ouvre-porte de garage directement à des support
de structures.
5.1 Mesurer, de chaque côté de l’ouvre-porte, la
distance entre l’ouvre-porte et les solives.
5.2 Couper les deux supports de suspension à la
longueur requise.
5.3 Percer des avant-trous de 3/16 pouce dans les
solives.
5.4 Fixer une extrémité de chaque support de
suspension sur une solive avec des tire-fond de
5/16 po -18 x 1-7/8 po. (non fournis).
5.5 Fixer l’ouvre-porte aux supports de suspension
à l’aide de boulons hexagonaux de 5/16 po-18 x
7/8 po, de rondelles-frein et d’écrous.
5.6 S’assurer que le rail est centré au-dessus de la
porte (ou dans le prolongement du support de
linteau si le support n’est pas centré au dessus
de la porte).
5.7 Retirer le 2 x 4. Faire fonctionner la porte
manuellement. Si la porte frappe le rail, lever le
support de linteau.
REMARQUE : NE PAS mettre l’ouvre-porte sous
tension à ce stade.
FIGURE 1
FIGURE 2
FIGURE 3
Plafond fini
Plafond Non-fini
Mesurer
la distance
(Non fournie)
Tire-fond de
5/16 po-18x1 7/8po
Boulon de 5/16 po-18 x 7/8 po, Rondelle frein de 5/16 po, Écrou de 5/16 po-18
(Non fournie)
Pose
5 Accrochage de l’ouvre-porte
… 48 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liftmaster 8587 Elite at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liftmaster 8587 Elite in the language / languages: English as an attachment in your email.

The manual is 14,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info