600894
24
Zoom out
Zoom in
Previous page
1/76
Next page
24
1 Program the
Travel
Withouta properly installed safetyreversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.
Incorrect adjustmentof garage door travel limits will interfere with proper operation of safety reversal system.
After ANY adjustments are made,the safetyreversal system MUSTbe tested.Door MUST reverse on contact with 1-1/2" (3.8 cm) high object(or 2x4 laid flat) on
floor.
1.1 Pressand hold the
AdjustmentButton until
the UP Button beginsto
flash and/or a beep is
heard.
1.2 Pressand hold the UP Button until the door is in
the desired UP position.
NOTE: The UPand DOWNButtons can be
used to move the door up and down as needed.
1.3 Once the door is in the desired UP position
press and release the AdjustmentButton.The
garage door opener lights will flash twice and
the DOWN Button will begin to flash.
1.4 Pressand hold the DOWN Button until the door
is in the desired DOWN position.
NOTE: The UPand DOWNButtons can be
used to move the door up and down as needed.
1.5 Once the door is in the
desired DOWN position
press and release the
AdjustmentButton.The
garage door opener
lights will flash twice
and the UP Button will
begin to flash.
1.6 Pressand release the UP Button.When the
door travelsto the programmed UP position,the
DOWN Button will begin to flash.
1.7 Pressand release the DOWNButton. The door
will travel to the programmed DOWN position.
Programming is complete.
If the garage door opener lightsare flashing 5 times
during the steps for Program the Travel,the
programming hastimed out. If the garage door opener
lights are flashing 10 times during the steps for
Program the Travel,the safetyreversing sensors are
misaligned or obstructed (refer to page 22). When the
sensors are aligned and unobstructed, cycle the door
through a complete up and down cycle using the
remote control or the UP and DOWNbuttons.
Programming is complete. Ifyou are unable to operate
the door up and down, repeat the steps for
Programming the Travel.
Adjustments
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liftmaster 8587 Elite at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liftmaster 8587 Elite in the language / languages: English as an attachment in your email.

The manual is 14,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info