600892
29
Zoom out
Zoom in
Previous page
1/41
Next page
29
Door Control
Using the Door Control
SYNCHRONIZETHEDOORCONTROL
To synchronize the door control to the garage door opener, pressthe push bar until the garage door
opener activates(it may take up to 3 presses).Testthe door control by pressing the push bar,each
press ofthe push bar will activate the garage door opener.
Push Bar
LIGHT
button
Scre
en
Motion
Sensor
Naviga
tion
Buttons
PUSH BAR
Press the push bar to open or close the door.
NAVIGATION BUTTONS
Use the navigation buttons to make selections and program features.
LIGHTBUTTON
Press the LIGHTbutton to turn the garage door opener lights on or off.When the lights are turned on
they will stay on until the LIGHT button ispressed again, or until the garage door opener isactivated.
Once the garage door opener isactivated the lights will turn offafter the specified period of time (the
factory setting is 4-1/2 minutes). The LIGHT button will not control the lights when the door is in motion.
SCREEN
The screen will display the time and temperature until the menu button is pressed, and then itwill display
the menu options. Ifthere is a problem with the garage door opener the screen will display the Diagnostic
Code. Refer to the Troubleshooting section.
The following features are accessible through the screenusingthe navigation buttons:
LEARN A DEVICE
Any compatible remote controls, wireless keyless entry, or MyQ
®
accessoriescan be programmed to the
garage door opener by accessing the menu and using the navigation buttons.
LOCK
The LOCK feature is designed to preventactivation of the garage door opener from remote controls
while still allowing activation from the door control and keyless entry.This feature is useful for added
peace ofmind when the home is empty (i.e. vacation).
TIMER-TO-CLOSE (TTC)
DO NOT enable TTC if operating a one-piece door. TTC isto be used ONLY with sectional doors.
Factory defaultissetto off.TTC can be setto automatically close your garage door from the fully open
position after a specified period oftime (1, 5, 10 minute intervalsor a custom setting up to 99 minutes).
The garage door opener will Beep and the lights will Flash before closing the door. The screen on the
door control can display the statusof the TTC.TTC WILL NOT work ifthe garage door opener is
operating by battery power or if the safetyreversing sensors are misaligned.This feature is NOT
intended to be the primarymethod of closing the door. A keyless entry should be installed in the event
of an accidental lock out when usingthis feature.
NOTE: Before enabling the TTC for the first time, or if you experience a power outage, cycle the garage
door opener open and closed to allow the TTC to set.
AUTOMATICLIGHT
Motion Sensor
Factory defaultissetto on. Thisfeature automatically turns on the garage door opener lights when
motion is sensed. The lightswill come on for the setperiod oftime,then shutoff. Ifusing the garage door
opener light asa work light disable the motion sensor,otherwise the light will turn offautomaticallyif you
are beyond the range of the sensor.
Light Feature
The lights will turn on when someone enters through the open garage door and the safetyreversing
sensor infrared beam is broken.
MAINTENANCE ALERT(MAS)
This feature assists the homeowner in ensuring the garage door opener system staysin good working
condition. When the garage door opener needs to be serviced (approximately 4500 garage door
opener cycles) the command (yellow) and service (red) LEDs will begin to alternately flash backand
forth. The factory setting for the MAS feature is off and can be activated at time of installation. Contact your
installing dealer for service.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liftmaster 8550 Elite at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liftmaster 8550 Elite in the language / languages: English as an attachment in your email.

The manual is 5,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info