600892
2
Zoom out
Zoom in
Previous page
1/41
Next page
2
Safety Symbol and Signal Word
Review
This garage door opener has been designed and
tested to offer safe service provided it isinstalled,
operated,maintained and tested in strict
accordance with the instructions and warnings
contained in this manual.
When you see these SafetySymbols and Signal
Words on the following pages,they will alertyou to
the possibility of serious injury or death if you do
not comply with the warningsthat accompanythem.
The hazard may come from something mechanical
or from electric shock. Read the warnings carefully.
Mechanical
Electrical
When you see thisSignal Word on the following
pages, itwill alertyou to the possibilityof damage to
your garage door and/or the garage door opener if
you do not comply with the cautionary statements
thataccompanyit. Read them carefully.
Check the Door
To preventpossible SERIOUSINJURYor
DEATH:
l ALWAYS call a trained door systems
technician if garage door binds,sticks,
or isout ofbalance. An unbalanced
garage door may NOTreverse when
required.
l NEVER try to loosen, move or adjust
garage door, door springs,cables,
pulleys,brackets or their hardware,
ALLof which are under EXTREME
tension.
l Disable ALLlocks and remove
ALLropes connected to garage door
BEFORE installation and operating
garage door opener to avoid
entanglement.
To preventdamage to garage door and
opener:
l ALWAYS disable locks BEFORE
installing and operating the opener.
l ONLY operate garage door opener at
120V, 60Hzto avoid malfunction and
damage.
1. Disable locksand remove any ropes
connected to the garage door.
2. Lift the door halfway up.Release the
door.If balanced, it should stay in place,
supported entirely by itssprings.
3. Raise and lower the door to check for
binding or sticking. Ifyour door binds,
sticks, or is out of balance,call a trained
door systems technician.
4. Check the seal on the bottomof the door.
Any gap between the floor and the
bottom of the door must not exceed
1/4inch (6 mm).Otherwise, the safety
reversal system may notwork properly.
5. The opener should be installed above
the center of the door. Ifthere is a torsion
spring or center bearing plate in the way
of the header bracket, it maybe installed
within 4feet (1.2 m) to the leftor right of
the door center.See page 7.
Torsion
Spring
Ex
tension
Spring
OR
Tools Needed
2
1
3/16
7/16
1/2
5/32
5/16
5/8
9/16
1/4
7/16
Preparation
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liftmaster 8550 Elite at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liftmaster 8550 Elite in the language / languages: English as an attachment in your email.

The manual is 5,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info