600903
29
Zoom out
Zoom in
Previous page
1/36
Next page
Children operating or playing with a garage door opener
can injure themselves or others.
The garage door could
close and cause serious injury or death.
Do not allow
children to operate the door control(s) or remote control
transmitter(s).
A moving garage door could injure or kill someone under
it.
Activate the opener only when you can see the door
clearly, it is free of obstructions, and is properly
adjusted.
“Security Plus”
Your garage door opener receiver and remote control
transmitter have been set at the factory to a matching
code. The door will activate when you press the LARGE
remote control push button.
Your "Security Plus" opener will operate with:
several Security Plus remote controls (with yellow
indicator lights) utilizing up to 8 functions. NOTE:
Open/Close/Stop operation counts as 1 function.
one Keyless Entry System (with Security Plus logo)
Follow the instructions below to program your opener to
match any additional remotes you may purchase. See
Accessories on page 34.
To Add a Remote Control
1. Press and hold the selected remote control push button.
See Figure 1.
2. Press and release the "Smart" (learn) button on the
right side panel of the opener. See Figure 2. The
indicator light on the panel will begin to blink and the
opener lights will flash once.
3. Release the remote push button.
Now the opener will operate when the remote control
push button is pressed. Test by pressing the remote button
to see that the door goes up and down.
Adding a remote can also be done from the door
control, as follows:
1. With the door closed, press and hold a remote push
button.
2. Press and hold the Light button on the door control.
3. Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button.
To Erase All Remote Control Codes
Press and hold the "Smart" button on the opener panel
until the indicator light turns off (about 6 seconds). All
transmitter codes are now erased. Then follow the steps
above to re-program each remote control.
To Control the Opener Lights
With Security Plus transmitters, a remote push button can
be programmed to operate the opener lights without
opening the door.
1. With the door closed, press and hold the remote button
that you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener
lights should turn on or off but the door should not move.
29
Select a 
push button
Yellow 
Battery Indicator
Light
Sélectionner un 
bouton-poussoir
Témoin lumineux 
jaune de
pile
Figure 1
WARNING
CAUTION
WARNING
Receiver & Remote Control Programming
NOTICE: To comply with FCC rules, adjustment or modification of this
receiver and/or transmitter are prohibited, except for changing the code
setting or replacing the transmitter battery. THERE ARE NO OTHER
USER SERVICEABLE PARTS.
Security Plus
Garage Door Opener
"Smart" (learn) 
Button
Indicator
Light
+
+
321
Kg
Kg
1
3
8
7
5
1
3
8
7
5
Code programming instructions are
also located on the opener panel.
Open/Close/Stop Operation
Your Security Plus remote control can be programmed to
operate one door using all 3 buttons: the large button will
only open the door, the middle button will only close the
door, and the third button will stop the door’s movement.
You may set up this feature as follows:
1. With the door closed, press and
hold the large remote push button.
2. Press and hold the Lock button
on the door control.
3. Press and hold the door control push bar.
When the opener lights flash, release all buttons. Test by
pressing the large (Open) button on the remote. The door
should open. Press it again while the door is open and
nothing should happen. Press the middle (Close) button
and the door should close. Press the third (Stop) button
while the door is moving and it should stop immediately.
Model 67LM Security Plus Keyless Entry
Follow instructions on page 34 (Accessories).
Open
Close
Stop
Ouverture
Fermeture
Arrêt
Security Plus Remote Control
Figure 2
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liftmaster 2000SDR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liftmaster 2000SDR in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info