600903
25
Zoom out
Zoom in
Previous page
1/36
Next page
Adjustment Step 2
Adjust the Force
Too much force on the door will interfere with the proper
operation of the safety reverse system.
The door might
not reverse properly when required and could seriously
injure or kill someone under it.
Do not increase the force
beyond the minimum amount required to close the door.
Do not use the force adjustments to compensate for a
binding or sticking garage door. Test the safety reverse
system monthly, and following all adjustments to force
levels. See page 26.
Force Adjustment Label
Right Side
Panel
Force Adjustment
Controls
Kg
Kg
Kg
Kg
1
3
8
7
5
1
3
8
7
5
1
3
8
7
5
1
3
8
7
5
+
+
321
How and When to Adjust the Forces
Test the DOWN (close) force
Grasp the door bottom when the door is about halfway
through DOWN (close) travel. The door should reverse.
Reversal halfway through down travel does not
guarantee reversal on a one-inch obstruction. See
page 26. If the door is hard to hold or doesn't reverse,
decrease the DOWN (close) force by turning the control
counterclockwise.
Make small adjustments until the door reverses normally.
After each adjustment, run the opener through a complete
cycle.
Test the UP (open) force
Grasp the door bottom when the door is about halfway
through UP (open) travel. The door should stop. If the
door is hard to hold or doesn't stop, decrease UP (open)
force by turning the control counterclockwise.
Make small adjustments until the door stops easily. After
each adjustment, run the opener through a complete
travel cycle.
If the door doesn't open at least 5 feet:
Increase UP (Open) force by turning the control
clockwise. Make small adjustments until door opens
completely. Readjust the UP limit if necessary. After each
adjustment, run the opener through a complete travel
cycle.
If the door reverses during the down (close) cycle and
the opener lights aren't flashing:
Increase DOWN (close) force by turning the control
clockwise. Make small adjustments until the door
completes a close cycle. After each adjustment, run the
opener through a complete travel cycle. Do not increase
the force beyond the minimum amount required to
close the door.
25
WARNING
Force adjustment controls are located on the right panel
of the opener. Force adjustment settings regulate the
amount of power required to open and close the door.
The door will stop in the up direction if anything
interferes with its travel. The door will reverse in the
down direction if anything interferes with its travel
(including binding or unbalanced doors).
If the forces are set too light, door travel may be
interrupted by nuisance reversals in the down direction
and stops in the up direction. Weather conditions can
affect the door movement, so occasional adjustment may
be needed.
The maximum force adjustment range is about 3/4 of a
complete turn. Do not force controls beyond that point.
Turn force adjustment controls with a screwdriver.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liftmaster 2000SDR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liftmaster 2000SDR in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info