600903
22
Zoom out
Zoom in
Previous page
1/36
Next page
Installation Step 13
Connect Door Arm to Trolley
Follow instructions which apply to your door type
as illustrated below and on page 23.
Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the
inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in Figures 1, 2 and 3.
Figure 2:
Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far apart
as possible to increase door arm rigidity.
Ring 
Fastener
Door
Bracket
Straight
Door Arm
Curved
Door Arm
Inner
Trolley
Outer
Trolley
Lock
Washers
5/16"
Nuts
5/16"-18
Door
Bracket
Screws
5/16"-18x7/8"
Cut this end
Manual
Release
Handle
Rope
Lock
Washers
5/16"
Nuts
5/16"-18
Screws
5/16"-18x7/8"
Clevis Pin
5/16"x1"
Clevis Pin
5/16"x1-1/4"
DoorArmTrolleySecScrew
6/96
Ring 
Fastener
Door
Bracket
Straight
Door Arm
Curved
Door Arm
Inner
Trolley
Outer
Trolley
Lock
Washers
5/16"
Nuts
5/16"-18
Door
Bracket
Screws
5/16"-18x7/8"
Cut this end
Manual
Release
Handle
Rope
Lock
Washers
5/16"
Nuts
5/16"-18
Screws
5/16"-18x7/8"
Clevis Pin
5/16"x1"
Clevis Pin
5/16"x1-1/4"
DoorArmTrolleySecScrew
6/96
Figure 3:
If holes in curved arm are
above holes in straight arm,
disconnect straight arm. Cut about 6" from the solid
end. Reconnect to trolley with cut end down as shown.
• Bring arm sections together.
• Find two pairs of holes that line up and join with
screws, lock washers and nuts.
Proceed to Adjustment Step 1, page 24.
Trolley will re-engage automatically when the
opener is operated.
22
Figure 1:
Fasten straight door arm section to outer trolley with
the 5/16"x1" clevis pin. Secure the connection with a
ring fastener.
• Fasten curved section to the door bracket in the same
way, using the 5/16"x1-1/4" clevis pin.
Figure 1
Figure 2
Figure 3
SECTIONAL Doors Only
Lock Washer 5/16"
Nut 5/16"-18
Ring Fastener
Hex Screw
5/16"-18x7/8"
Clevis Pin
5/16"x1" (Trolley)
Clevis Pin
5/16"x1-1/4" (Door Bracket)
Hdw for door EN/FR
Hardware Shown Actual Size
Hole Alignment Alternative
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liftmaster 2000SDR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liftmaster 2000SDR in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info