552418
12
Zoom out
Zoom in
Previous page
1/16
Next page
11
6. Install the Handlebar and Computer.
Remove four M5x12 Bolts (57) from the back of the
Computer (56).
Remove two M8x16 Bolts (41) and Ø20xØ8 Curve
Washers (42) from the Front Post (5).
Insert the Hand Pulse Sensor Wires (69) from the
Handlebar (6) into the hole on the Front Post (5) and
then pull them out from the top end of the Front Post
(5). Attach the Handlebar onto the Front Post (5)
with two M8x16 Bolts (41) and Ø20xØ8 Curve
Washers (42) that were removed.
Connect the Sensor Wire I (67) and Hand Pulse
Sensor Wires (69) to the wires that come from the
Computer (56) and then attach the Computer (56)
onto the top end of the Front Post (5) with four
M5x12 Bolts (57) that were removed.
7. Install the Seat Post, Seat Sliding Tube, and
Seat Cushion.
Slide the Seat Post Cover (98) onto the tube of the
Main Frame (1).
Insert the Seat Post (93) into the bushing on the tube
of the Main Frame (1) and then attach the Locking
Knob (95) onto the tube of the Main Frame (1) by
turning it in a clockwise direction to lock the Seat
Post (93) in the suitable position.
Adjusting the seat post:
Turn the Locking Knob (95) in a counterclockwise
direction until it can be pulled out. Pull out the Locking Knob (95) and then slide the Seat
Post (93) up or down direction to the suitable position. Lock the Seat Post (93) in place by
releasing the Locking Knob (91) and sliding the Seat Post (93) up or down slightly until the
Locking Knob (95) "pops" down into the locked position. For added safety, tighten the
Locking Knob (95) in a clockwise direction.
NOTE: When adjusting the height of seat post, the maximum insert depth mark line
cannot higher than the edge of seat post cover.
Remove three M8 Nylon Nuts (24) and Ø16xØ8x1.5 Washers (25) from underneath of the
Seat Cushion (97). Then attach the Seat Cushion (97) onto the triangle plate of Seat
Sliding Tube (91) with three M8 Nylon Nuts (24) and Ø16xØ8x1.5 Washers (25) that were
removed.
Remove one Ø26xØ8x2 Big Washer (34) and M8 Round Knob (94) from underneath of the
Seat Sliding Tube (91) and then attach the Seat Sliding Tube (91) onto the Seat Post (93)
with one Ø26xØ8x2 Big Washer (34) and M8 Round Knob (94) that were removed.
Adjusting the seat cushion:
Release the Round Knob (94) and then slide the Seat Sliding Tube (91) forth or back
direction for the suitable position. Tighten the Round Knob (94) after adjustment.
5
56
67
57
69
42
41
6
69
93
98
95
1
97
34
94
91
25
24
6
7
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LifeGear Streamline Plus - Two In One Elliptical Bike 93566 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LifeGear Streamline Plus - Two In One Elliptical Bike 93566 in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info