552421

LifeGear Streamline Plus - Magnetic Recumbent Bike 26560 Manual

9
Zoom out
Zoom in
Previous page
1/14
Next page
8
ASSEMBLY INSTRUCTIONS
1. Install the Front and Rear Stabilizers.
Attach the Front Stabilizer (2) onto the front curve plate
of the Front Main Frame (5) with two M10x57 Bolts (30),
Ø10 Curve Washers (31), and M10 Cap Nuts (32).
Attach the Rear Stabilizer (4) onto the rear curve plate of
the Rear Main Frame (3) with two M10x57 Bolts (30),
Ø10 Curve Washers (31), and M10 Cap Nuts (32).
2. Install the Front Handlebar Post, Tension
Control Knob, and Pedals.
Remove one M8x15 Bolt (23), Ø8 Curve Washer
(25), four Ø8 Flat Washers (24), and M8x10 Bolts
(76) from the tube of the Front Main Frame (5).
Slide the Front Handlebar Post Cover (73) up from the
bottom end of the Front Handlebar Post (6).
Insert the Tension Cable (40) through into the bottom
hole of Front Handlebar Post (6) and pull it out from the
square hole of Front Handlebar Post (6).
Connect the Extension Hand Pulse Sensor Wires (65)
from the Front Main Frame (5) to the Extension Wires
(63) from the Front Handlebar Post (6).
Connect the Sensor Wire (61) from the Front Main
Frame (5) to the Extension Sensor Wire (64) from the
Front Handlebar Post (6).
Insert the Front Handlebar Post (6) onto the tube of the
Front Main Frame (5) and secure with one M8x15 Bolt
(23), Ø8 Curve Washer (25), four Ø8 Flat Washers (24), and M8x10 Bolts (76) that were
removed. Be careful not to pinch the cables inside the Front Handlebar Post (6) when
turning the M8x10 Bolts (76).
Slide the Front Handlebar Post Cover (73) down onto the tube of the Front Main Frame (5).
Remove the M5x25 Bolt (36) and Ø5 Flat Washer (38) from the Tension Control Knob (14).
Put the cable end of resistance cable of Tension Control Knob (14) into the spring hook of
Tension Cable (40) as shown in drawing A of figure 2. Pull the resistance cable of Tension
Control Knob (14) up and force it into the gap of metal bracket of Tension Cable (40) as
shown in drawing B of figure 2. Attach the Tension Control Knob (14) onto the Front
Handlebar Post (6) with the M5x25 Bolt (36) and Ø5 Flat Washer (38) that were removed.
Connect the Left Pedal (59) to the left Crank (46). Thread it into the crank assembly in the
counterclockwise direction by the tool provided.
Connect the Right Pedal (60) to the right Crank (46) by threading it in the clockwise direction.
NOTE: The Left and Right Pedals (59, 60) and Crank (46) are marked with “L” & “R” (left and
right).
3
2
5
30
32
31
31
14
40
14
40
BA
30
4
76
76
36
38
6
40
61
14
63
64
32
46
73
24
23
25
24
65
40
63
64
5
59
60
1
2
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LifeGear Streamline Plus - Magnetic Recumbent Bike 26560 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LifeGear Streamline Plus - Magnetic Recumbent Bike 26560 in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info