552406

LifeGear Magnetic Upright Bike 23500 Manual

20
Zoom out
Zoom in
Previous page
1/24
Next page
19
4. Install the Seat Cushion, Seat Post and
Left/Right Seat Sliding Tubes.
Release both M8 Nuts (100) just a little bit from
underneath of the Seat Cushion (69) and then attach
the Seat Sliding Tube (6) with Seat Post (5) onto the
hole that underneath of the Seat Cushion (69).
Tighten both M8 Nuts (100) after adjustment.
Attach the Seat Height Adjusting Knob (62) onto the
tube of Main Frame (1) on the Seat Post Cover (78)
by turning it in a clockwise direction. Release the
Seat Height Adjusting Knob (62) by turning it in a
counterclockwise direction until it can be pulled out.
Pull out the Seat Height Adjusting Knob (62) and
slide the Seat Post (5) into the bushing on the tube
of the Main Frame (1). Lock the Seat Post (5) in
place by releasing the Seat Height Adjusting Knob
(62) and sliding the Seat Post (5) up or down slightly
until the Seat Height Adjusting Knob (62) "pops"
down into the locked position. For added safety,
tighten the Seat Height Adjusting Knob (62) in a
clockwise direction.
Attach the Left and Right Seat Sliding Tube Covers
(79, 80) onto the top end of the Seat Post (5) with
two M4x25 (UCP) Screws (28) and M4x8 Screws
(29).
NOTE: When adjusting the height of seat post,
the maximum insert depth mark line cannot
higher than the edge of bushing.
5. Install the Handlebar and Computer.
Install the Handlebar (8) to the groove of the Front
Post (4). Insert the Hand Pulse Wire (93) into the
hole on the Front Post (4) and then pull it out from
the top end of the Front Post (4). Install the Wire
Plug (83) onto the hole on the Front Post (4).
Remove four M5x12 Bolts (95) from the Computer
(85). Connect the Hand Pulse Wire (93) and
Sensor Wire I (90) to the wires that come from the
Computer (85) and then attach the Computer (85)
onto the top end of the Front Post (4) with four
M5x12 Bolts (95) that were removed.
Attach the Front and Back Handlebar Covers (81, 82)
onto the Handlebar (8) and Front Post (4) with two
M5x10 (UCP) Bolts (26) and M3x12 Screws (27).
Tighten the T-Knob (63) after adjustment.
6. Install the Pedals and Adaptor.
Attach the Right and Left Pedals (68R, 68L) to the
Right and Left Cranks (72R, 72L). The Right Pedal
(68R) should be threaded in a clockwise direction.
The Left Pedal (68L) should be threaded in a counterclockwise direction.
Plug the wire of the Adaptor (87) into the power jack on the rear side of the Left Shroud (74)
and then connect the Adaptor (87) to the electrical wall outlet.
NOTE: The Right and Left Pedals (68R, 68L) and Right and Left Cranks (72R, 72L) are
marked with “R” & “L”.
4
5
6
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LifeGear Magnetic Upright Bike 23500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LifeGear Magnetic Upright Bike 23500 in the language / languages: English as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info