552465

LifeGear Jupiter - 2 in 1 Elliptical Trainer 93726 Manual

11
Zoom out
Zoom in
Previous page
1/21
Next page
10
2. Front Post and Tension Control Knob Installation
Insert the Tension Cable (30) through into the bottom hole of Front Post (5) and pull it out
from the square hole of Front Post (5).
Connect the Sensor Wire (68) from the Main Frame (1) to the Extension Sensor Wire (67)
from the Front Post (5).
Insert the Front Post (5) onto the tube of the Main Frame (1) and secure with six M8x16
Bolts (41), six Ø8 Spring Washers (60), and six Ø20xØ8 Curve Washers (42). Tighten
bolts with the 5mm Allen Wrench with Phillips Screwdriver provided.
Remove the Ø20xØ5.2 Curve Washer (64) and M5x25 Bolt (65) from the Tension Control
Knob (55). Remove bolt with the 5mm Allen Wrench with Phillips Screwdriver provided.
Put the cable end of resistance cable of Tension Control Knob (55) into the spring hook of
Tension Cable (30), see Figure A. Pull the resistance cable of Tension Control Knob (55)
up and force it into the gap of metal bracket of Tension Cable (30), see Figure B. Attach the
Tension Control Knob (55) onto the Front Post (5) with the Ø20xØ5.2 Curve (64) and M5x25
Bolt (65) that were removed. Tighten bolt with the 5mm Allen Wrench with Phillips
Screwdriver provided.
Hardware:
1
5
54
54
30
30
30
60
60
64
65
68
67
41
42
41
55
BA
30
42
Allen Wrench with Phillips
Screwdriver 5mm
Tool:
(41) Bolt M8x16
6 PCS
(60) Spring Washer Ø8
6 PCS
(42) Curve Washer
Ø20xØ8
6 PCS
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LifeGear Jupiter - 2 in 1 Elliptical Trainer 93726 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LifeGear Jupiter - 2 in 1 Elliptical Trainer 93726 in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info