552415

LifeGear Evoke - Recumbent Bike 26290 Manual

11
Zoom out
Zoom in
Previous page
1/17
Next page
10
3. Front Handlebar Post and Foot Pedal Installation
Remove four M8x15 Bolts (23) and Ø8 Curve Washers (25) from the Front Main Frame (5).
Slide the Front Handlebar Post Cover (74) up to the Front Handlebar Post (6).
Insert the Tension Cable (40) through into the bottom hole of Front Handlebar Post (6) and
pull it out from the square hole of Front Handlebar Post (6).
Connect the Sensor Wire (61) and Extension Hand Pulse Sensor Wires (65) from the Front
Main Frame (5) to the Extension Sensor Wire (64) and Extension Wires (63) from the Front
Handlebar Post (6).
Insert the Front Handlebar Post (6) onto the tube of the Front Main Frame (5) and secure
with four M8x15 Bolts (23) and Ø8 Curve Washers (25) that were removed. Slide the
Front Handlebar Post Cover (74) down to the Front Main Frame (5).
Remove the M5x45 Bolt (36) and Ø5 Big Curve Washer (38) from the Tension Control Knob
(14). Put the cable end of resistance cable of Tension Control Knob (14) into the spring
hook of Tension Cable (40) as shown in drawing A of figure 3. Pull the resistance cable of
Tension Control Knob (14) up and force it into the gap of metal bracket of Tension Cable (40)
as shown in drawing B of figure 3. Attach the Tension Control Knob (14) onto the Front
Handlebar Post (6) with the M5x45 Bolt (36) and Ø5 Big Curve Washer (38) that were
removed.
The Cranks, Foot Pedals, Pedal Shafts and Pedal Straps are marked “R” for Right and
“L” for Left.
Insert the pedal shaft of Left Foot Pedal (60) into threaded hole in the left Crank (46).
Turn the pedal shaft by hand in the counter-clockwise direction until snug.
Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the
threads.
Tighten the pedal shaft of Left Foot Pedal (60) with the Multi Hex Tool with Phillips
Screwdriver provided.
Insert pedal shaft of Right Foot Pedal (59) into threaded hole in right Crank (46).
Turn the pedal shaft by hand in the clockwise direction until snug.
Tighten pedal shaft of Right Foot Pedal (59) with the Multi Hex Tool with Phillips Screwdriver
provided.
55
40
64
64
63
74
14
36
38
6
59
23
60
5
25
46
23
25
23
25
61
40
65
Allen Wrench S6
Tool:
Multi Hex Tool with
Phillips Screwdriver
14
BA
14
40
40
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LifeGear Evoke - Recumbent Bike 26290 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LifeGear Evoke - Recumbent Bike 26290 in the language / languages: English as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info