710417

Liebherr TP 1764-22 Manual

7
Zoom out
Zoom in
Previous page
1/14
Next page
-
The cross section of the ventilation gap below the ceiling
must be at least 300 cm
2
.
-
the larger the ventilation space, the more energy-saving the
appliance is in operation.
If the appliance is installed with the hinges next to a wall
Fig. 8 (4)
, the distance between appliance and wall has to be at
least 40 mm. This corresponds to the projection of the handle
when the door is open.
4.5 Disposing of packaging
WARNING
Danger of suffocation due to packing material and plastic film!
u
Do not allow children to play with packing material.
The packaging is made of recyclable materials:
-
corrugated board/cardboard
-
expanded polystyrene parts
-
polythene bags and sheets
-
polypropylene straps
-
nailed wooden frame with polyethylene panel*
u
Take the packaging material to an official collecting point.
4.6 Connecting the appliance
NOTICE
Failure to connect properly
Damage to the electronics.
u
Do not use a standalone inverter.
u
Do not use an energy saving plug.
WARNING
Failure to connect properly
Fire hazard.
u
Do not use an extension cable.
u
Do not use distributor blocks.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see 1 Appliance at a glance) .
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It
must be outside the area of the rear of the appliance.
u
Check the electrical connection.
u
Plug in the power plug.
4.7 Switching on the appliance
u
Press On/Off button
Fig. 3 (1)
.
w
The appliance is switched on. The temperature display indi-
cates the set temperature.
w
If “DEMO” is displayed, demo mode is activated. Please
contact the after sales service.
5 Control
5.1 Brightness of the temperature
display
You can adjust the brightness of the temperature display to the
light conditions of the room in which the appliance is installed.
5.1.1 Setting the brightness
The brightness is adjustable between h 0 (minimum bright-
ness) and h 5 (maximum brightness).
u
Activate setting mode by pressing the SuperFrost* button
Fig. 3 (3)
/SuperCool* button
Fig. 3 (4)
for approx. 5 sec.
w
The Menu symbol is shown on the display,
Fig. 3 (5)
.
w
c flashes on the display.
u
Use the adjustment button,
Fig. 3 (2)
, to select h.
u
Briefly confirm with the SuperFrost* button
Fig. 3 (3)
/Super-
Cool* button
Fig. 3 (4)
.
w
The display shows the last set brightness value.
u
Use the adjustment button,
Fig. 3 (2)
, to set the desired
value from h 0 to h 5.
u
Briefly confirm the newly set brightness value with the
SuperFrost* button
Fig. 3 (3)
/ SuperCool* button
Fig. 3 (4)
.
w
h flashes on the display.
w
The brightness is set.
u
After making the change, deactivate setting mode: Press the
On/Off button
Fig. 3 (1)
once.
w
The temperature display shows the temperature again.
If setting mode is already activated but you would like to keep
the old brightness value setting:
u
Press the On/Off button
Fig. 3 (1)
twice to deactivate setting
mode.
w
The temperature display shows the temperature again.
5.2 Child proofing
The child-proofing function enables you to make
sure that the appliance is not inadvertently switched
off by playing children.
5.2.1 Setting the child lock
To switch on the function:
u
Activate setting mode: press SuperFrost* button
Fig. 3 (3)
/
SuperCool* button
Fig. 3 (4)
for approx. 5 seconds.*
w
The Menu symbol
Fig. 3 (5)
is shown on the display.
w
c flashes on the display.
u
Briefly confirm with the SuperFrost* button
Fig. 3 (3)
/Super-
Cool* button
Fig. 3 (4)
.*
w
c1 appears in the display.
u
Briefly confirm with the SuperFrost* button
Fig. 3 (3)
/Super-
Cool* button
Fig. 3 (4)
.*
w
The child lock symbol
Fig. 3 (7)
, lights up on the
display.
w
c flashes on the display.
w
The child lock function is switched on.
If setting mode is to be terminated:
u
Briefly press the On/Off button
Fig. 3 (1)
.
-or-
u
Wait for 5 minutes.
w
The temperature display shows the temperature again.
To switch off the function:
u
Activate setting mode: press the SuperFrost* button
Fig. 3 (3)
/SuperCool* button
Fig. 3 (4)
for
approx. 5 seconds.*
w
The Menu symbol
Fig. 3 (5)
is shown on the display.
w
c flashes on the display.
u
Briefly confirm with the SuperFrost* button
Fig. 3 (3)
/Super-
Cool* button
Fig. 3 (4)
.*
w
c0 appears in the display.
u
Briefly confirm with the SuperFrost* button
Fig. 3 (3)
/Super-
Cool* button
Fig. 3 (4)
.*
w
The child lock symbol
Fig. 3 (7)
goes out.
Control
* Depending on model and options 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr TP 1764-22 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr TP 1764-22 in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr TP 1764-22

Liebherr TP 1764-22 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info