715385
27
Zoom out
Zoom in
Previous page
1/30
Next page
The fuse of the wall socket is not in order.
u
Check fuse.
The appliance plug does not fit the appliance properly.
u
Check the appliance plug.
The compressor runs for a long time.
The compressor switches to a low speed when little cold is
needed. Although the running time is increased as a result,
energy is saved.
u
This is normal in energy-saving models.
SuperFrost is activated.
u
The compressor runs for longer in order to rapidly cool the
food. This is normal.
Excessive noise.
Due to the various speed steps, speed-regulated* compres-
sors can generate different running noises.
u
The sound is normal.
A bubbling and gurgling noise.
This noise comes from the refrigerant flowing in the refriger-
ation circuit.
u
The sound is normal.
A quiet clicking noise.
The noise is produced whenever the refrigeration unit
(motor) automatically switches on or off.
u
The sound is normal.
A hum. It is briefly a little louder when the refrigeration
unit (the motor) switches on.
The refrigeration increases automatically when the
SuperFrost, function is activated, fresh food has just been
placed in the appliance or the door has been left open for a
while.
u
The sound is normal.
The ambient temperature is too high.
u
Solution: (see 1.2 Appliance range of use)
A low hum.
The sound is produced by air flow noise of the fan.
u
The sound is normal.
Vibration noises
The appliance is not standing firmly on the floor. As a result
objects and adjacent units start to vibrate when the refriger-
ator is running.
u
Align the appliance using the adjustable feet.
u
Keep bottles and jars apart.
Flow sound at the soft stop mechanism.
The noise is produced when the door is opened and
closed.
u
The sound is normal.
Mould on wine bottles
Similarly as with other forms of storage, a little mould may
form depending on the type of adhesive used for the label.
u
Remove residual adhesive.
The DEMO symbol appears on the screen. In addition
some time elapses.
DEMO mode is activated.
u
OFF Press .
DEMO is displayed in the top right corner of the screen.
DEMO mode is activated.
u
Unplug the appliance.
u
Plug the appliance in again.
w
The DEMO symbol appears on the screen. In addition some
time elapses.
u
OFF Press .
The outer surfaces of the appliance are warm*.
The heat of the refrigeration circuit is used to prevent
condensate from forming.
u
This is normal.
The IceMaker cannot be switched on.
The appliance and therefore the IceMaker are not
connected.
u
Connect the appliance to the mains (see 4 Putting into
operation) .
The IceMaker does not make any ice cubes.
The IceMaker is not switched on.
u
Switch on the IceMaker.
The drawer of the IceMaker is not properly closed.
u
Close the drawer properly.
The water connection is not open.
u
Open the water connection.
Functions in the IceMaker submenu do not start.
Ice cube tray rotates.
u
Try again after 1 minute.
The temperature is not cold enough.
The door of the appliance is not properly closed.
u
Close the door of the appliance.
Insufficient ventilation.
u
Keep ventilation grille clear, and clean it.
The ambient temperature is too high.
u
Solution: (see 1.2 Appliance range of use) .
The appliance was opened too frequently or for too long.
u
Wait to see whether the appliance reaches the required
temperature by itself. If not, please contact the after sales
service (see 6 Maintenance) .
Too much fresh food was placed inside without SuperFrost.
u
Solution: (see 5.4.5 SuperFrost)
The temperature is incorrectly set.
u
Set the temperature to a colder setting and check after 24
hours.
The appliance is too close to a source of heat (stove, heater
etc).
u
Change the position of the appliance or the source of heat.
The internal light does not come on.
The appliance is not switched on.
u
Switch the appliance on.
The door was open for longer than 15 minutes.
u
The internal light switches itself off automatically after about
15 minutes if the door is open.
The LED illumination is faulty or the cover is damaged:
WARNING
Risk of injury due to electric shock!
Live parts are located under the cover.
u
Have the LED interior light changed or repaired only by the
customer service or by specialized personnel trained for the
purpose.
WARNING
Danger of injury by LED lamp!
The light intensity of the LED lighting corresponds to risk group
RG 2.
If the cover is defective:
u
Do not look into the illumination with optical lenses from the
immediate proximity. This can cause injury to the eyes.
The door seal is defective or needs to be replaced for
another reason.
The door seal can be replaced. It can be replaced without
the need for special tools.
u
Contact Customer Service (see 6 Maintenance) :
The unit has iced up or condensation has formed.
The door seal may have also slipped out of its groove.
Malfunctions
* Depending on model and options 27
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr SBSes 8496 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr SBSes 8496 in the language / languages: English as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr SBSes 8496

Liebherr SBSes 8496 Installation Guide - German - 6 pages

Liebherr SBSes 8496 User Manual - German - 30 pages

Liebherr SBSes 8496 User Manual - Dutch - 62 pages

Liebherr SBSes 8496 User Manual - French - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info