Manual Liebherr kt 1710 (page 7 of 14) (English)

344173

Zoom out

Zoom in

1/14

Fig. 8

Insert the spacer

Fig. 8 (13)

back under the right-hand side

of the door, as it is important for the stability of the appliance.

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough,

the door may drop out. This may lead to severe injuries. What is

more, the door may not close and therefore the appliance may

fail to cool properly.

Screw on the bearing brackets/bearing pins tightly (4 Nm).

Check all of the screws and retighten if necessary.

4.4 Undercounter installation

WARNING

Fire hazard from short-circuiting!

When pushing the appliance into the recess, take care not to

crush, jam or damage the mains power cable.

Do not operate the appliance with a defective mains power

cable.

Counter height appliances up to 850 mm in height can be

installed below the worktop. In the case of continuous work-

tops, the cover on the refrigerator can be removed and the

appliance slid in under the worktop.

With such installations, the plug

Fig. 9 (1)

must not be located

behind the appliance and must be easily accessible.

For the purpose of ventilation and aeration at the rear of the

appliance, a min.140 cm

ventilation cavity is required. With an

installation depth of 600 mm, the wall connection profile on the

worktop must not exceed a max. 10 mmin depth.

Fig. 9

In order to take off the appliance cover:

Remove the screws

Fig. 9 (2)

from the rear side.

Raise the cover up at the back, slide forward and lift up and

off the appliance.

4.5 Insertion into a row of kitchen units

Fig. 10

(1) Stack cabinet* (3) Kitchen cabinet*

(2) Appliance* (4) Wall*

For appliances supplied with wall spacers, the measurement

increases by 35 mm (see 4.2 Installing the appliance) .

The appliance can be built into kitchen units. A top cupboard

Fig. 10 (2)

can be added above the appliance in order to bring

the appliance

Fig. 10 (1)

up to the height of the fitted kitchen

units.

When installing with kitchen units (max. depth 580 mm), the

appliance can be positioned directly next to the kitchen cabinet

Fig. 10 (3)

. The appliance will project by 34 mm

at the sides

and 50 mm

in the centre of the appliance in relation to the

kitchen cabinet front.*

NOTICE

Danger of overheating due to insufficient air ventilation!

The compressor may be damaged if there is insufficient air

ventilation.

Take care to ensure adequate air ventilation.

Observe the ventilation requirements.

Ventilation requirements:

At the back of the stack cabinet there has to be a ventilation

duct of at least 50 mm depth throughout the width of the

stack cabinet.

The cross section of the ventilation gap below the ceiling

must be at least 300 cm

the larger the ventilation space, the more energy-saving the

appliance is in operation.

If the appliance is installed with the hinges next to a wall

Fig. 10 (4)

, the distance between appliance and wall has to be

at least 40 mm. This corresponds to the projection of the

handle when the door is open.*

4.6 Disposing of packaging

WARNING

Danger of suffocation due to packing material and plastic film!

Do not allow children to play with packing material.

The packaging is made of recyclable materials:

corrugated board/cardboard

expanded polystyrene parts

polythene bags and sheets

polypropylene straps

nailed wooden frame with polyethylene panel*

Putting into operation

* Depending on model and options 7

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr kt 1710 in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr kt 1710

Liebherr kt 1710 User Manual - Dutch - 9 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr kt 1710 Manual

Product: