355729

Liebherr kes 3660 inox Manual

17
Zoom out
Zoom in
Previous page
1/26
Next page
u
Remove the cover
Fig. 6 (27)
.*
u
Fully retract the adjustable-height foot
Fig. 6 (22)
.
u
If necessary, tip the appliance back a little with the assistance
of a second person for removal of the bearing pin.
u
Pull out the bearing pin
Fig. 6 (22)
downwards and forwards.
In so doing, pay attention to the hinge bush
Fig. 6 (20)
.
u
Unscrew the turn hinge
Fig. 6 (23)
(2 Torx 25)
Fig. 6 (24)
.
u
Unscrew the bearing part
Fig. 6 (26)
(1 Torx 25),
Fig. 6 (28)
.
u
Carefully lift off and transfer the cover
Fig. 6 (25)
on the handle
side.
u
Screw down the turn hinge
Fig. 6 (23)
on the new hinge side,
possibly with the aid of a cordless screwdriver, through the
outer oblong hole and round hole.
Note
u
If necessary, e.g. to make up for any unevenness in the floor,
the second oblong hole can be used instead of the round hole
for the screw fitting.
u
Tip the appliance back a little
again and re-insert the bear-
ing pin
Fig. 7 (22)
. The notch
has to point forwards.
u
Place the cover
Fig. 6 (27)
on
the opposite side.*
Fig. 7
CAUTION
Risk of injury if the door tips!
u
The safety lock
(21)
has to engage with the turn hinge at the
side so that the bearing pin and therefore the door are se-
cured.
u
u
Snap the safety lock
(21)
onto the turn hinge again.
u
Put on the hinge bush
Fig. 6 (20)
.
4.1.5 Transferring the handles
u
Disengage the spring clip
Fig. 8 (31)
from the upper door and
transfer it to the new hinge side.
u
Lift the stoppers
Fig. 8 (30)
out of the door bearing bushes and
transfer them.
Fig. 8
u
Detach the door handles
Fig. 8 (32)
, stoppers
Fig. 8 (33)
and
pressure plates
Fig. 8 (34)
and transfer to the opposite side.
u
When fitting the pressure plates at the opposite side, pay at-
tention that they engage properly.
4.1.6 Fitting the lower door
u
Place the lower door from above onto the lower bearing pin
Fig. 6 (22)
.
u
Close the door.
u
Place the plastic cap
Fig. 5 (10)
back onto the middle turn
hinge
Fig. 5 (13)
.
u
Place the middle bearing pin
Fig. 5 (11)
in the lower door, on
the new hinge side, through the middle turn hinge
Fig. 5 (13)
.
4.1.7 Fitting the upper door
u
Place the upper door on the middle bearing pin
Fig. 5 (11)
.
u
Insert the upper turn hinge
Fig. 4 (3)
in the door on the new
hinge side.
u
Screw down the upper turn hinge (2 Torx 25)
Fig. 4 (4)
. Pos-
sibly make preliminary holes with a bradawl or use a cordless
screwdriver.
u
Apply the cover
Fig. 4 (1)
and cover
Fig. 4 (2)
to the opposite
side from the outside and snap them into place.
4.1.8 Aligning the doors
u
Transfer the middle screw of the lower turn hinge
Fig. 6 (23)
into the free oblong hole.
u
If necessary, align the doors to the appliance housing by way
of the two oblong holes in the lower turn hinge
Fig. 6 (23)
and
middle turn hinge
Fig. 5 (13)
.
u
Tighten the screws.
4.2 Water connection
WARNING
Danger of electric shock!
u
Disconnect the appliance by unplugging it before you connect
it to the water line.
u
Shut off the water supply before you connect the water feed
lines of the IceMaker.
u
The connection to the drinking water system may be carried
out only by a qualified gas fitter and plumber.
WARNING
Risk of poisoning!
u
The water quality has to comply with the drinking water ordi-
nance of the respective country (e.g. 98/8
u
The IceMaker serves exclusively for making ice cubes in
household quantities and has to be operated with water suit-
able for the purpose.
Putting into operation
5
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr kes 3660 inox at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr kes 3660 inox in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr kes 3660 inox

Liebherr kes 3660 inox User Manual - Dutch - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info