Manual Liebherr k 4260 tgl (page 5 of 26) (English)

359465

Zoom out

Zoom in

1/26

Tip the appliance back a little

again and re-insert the bear-

ing pin

Fig. 6 (22)

. The notch

has to point forwards.

Place the cover

Fig. 5 (27)

the opposite side.*

Fig. 6

CAUTION

Risk of injury if the door tips!

The safety lock

(21)

has to engage with the turn hinge at the

side so that the bearing pin and therefore the door are se-

cured.

Snap the safety lock

(21)

onto the turn hinge again.

Put on the hinge bush

Fig. 5 (20)

4.1.3 Transferring the handle

Disengage the spring clip

Fig. 7 (34)

from the door and transfer

it to the new hinge side.

Lift the stopper

Fig. 7 (30)

out of the door bearing bush and

transfer it.

Fig. 7

Detach door handle

Fig. 7 (31)

, stoppers

Fig. 7 (32)

and pres-

sure plates

Fig. 7 (33)

plates and transfer to the opposite side

When fitting the pressure plates at the opposite side, pay at-

tention that they engage properly.

4.1.4 Fitting the lower door

Place the door from above onto the lower bearing pin

Fig. 5 (22)

Close the door.

Insert the upper turn hinge

Fig. 4 (12)

in the door on the new

hinge side.

Screw down the upper turn hinge

Fig. 4 (12)

(2 Torx 25)

Fig. 4 (13)

. Possibly make preliminary holes with a bradawl or

use a cordless screwdriver.

Snap the cover

Fig. 4 (10)

and cover

Fig. 4 (11)

into place at

the opposite side.

4.1.5 Aligning the door

Transfer the middle screw on the lower turn hinge

Fig. 5 (23)

into the free oblong hole.

Align the door to the appliance housing by way of the two ob-

long holes in the lower turn hinge

Fig. 5 (23)

Tighten the screws.

4.2 Insertion into a row of kitchen units

Fig. 8

(1) Stack cabinet (3) Kitchen cabinet

(2) Appliance (4) Wall

The appliance can be inserted into a row of kitchen units. To

match the appliance

Fig. 8 (2)

to the height of the row of units, a

suitable stack cabinet

Fig. 8 (1)

can be fitted above the appliance.

When inserting the appliance into a row of standard kitchen units

(max. depth 580 mm), the appliance can be installed directly next

to the kitchen unit

Fig. 8 (3)

. The appliance door projects relative

to the front of the kitchen unit by 34 mm at the side and by

50 mm in the middle of the appliance. It can be opened and

closed perfectly as a result.

Important for the ventilation:

At the back of the stack cabinet there has to be a ventilation

duct of at least 50 mm depth throughout the width of the stack

cabinet.

The ventilation space under the ceiling has to be at least

300 cm

The larger the ventilation space, the more energy-saving the

appliance is in operation.

If the appliance is installed with the hinges next to a wall

Fig. 8 (4)

, the distance between appliance and wall has to be at

least 36 mm. This corresponds to the projection of the handle

when the door is open.

4.3 Transporting the appliance

CAUTION

Risk of injury and danger of damage as a result of incorrect trans-

port!

Transport the appliance in a packed condition.

Transport the appliance upright.

Do not transport the appliance without assistance.

4.4 Installing the appliance

In the event that the appliance is damaged, contact the supplier

immediately before connecting to the mains.

The floor at the site must be flat and level.

Do not install the appliance in a location where it is exposed to

direct radiation of the sun, next to a cooker, heater and similar.

Putting into operation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr k 4260 tgl in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr k 4260 tgl

Liebherr k 4260 tgl User Manual - Dutch - 9 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr k 4260 tgl Manual

Product: