710373

Liebherr K 3130-20 Manual

6
Zoom out
Zoom in
Previous page
1/14
Next page
4.3 Changing over the door hinges
You can change over the door hinges if necessary.
Ensure that the following tools are to hand:
q
Torx 25
q
Torx 15
q
Screwdriver
q
Open-ended spanner included in supply package
q
Second person for fitting work, if needed
CAUTION
Risk of injury if the door tips!
u
Take good hold of the door.
u
Set down the door carefully.
Fig. 5
u
Remove the spacer
Fig. 5 (22)
from the bottom left of the
door.
u
Unscrew the securing screw on
the bottom right turn hinge.
u
Open the door.
u
Hold the door on the handle side
and at the bottom and lift it.
w
The bearing pin
Fig. 6 (21)
should
come out of the turn hinge
Fig. 7 (2)
.
u
If the bearing bolt
Fig. 6 (21)
doesn't undo press it out from
underneath.
Fig. 6
u
Swing door out at the bottom and remove it.
Fig. 7
u
Unscrew the turn hinge
Fig. 7 (2)
.
u
Unscrew the bearing element,
Fig. 7 (3)
transfer it to the
opposite location hole of the turn hinge and screw it firmly
into place.
u
Take the stopper
Fig. 7 (4)
out of the turn hinge and transfer
it to the receiving hole on the opposite side of the turn hinge.
u
Carefully lift off the cover
Fig. 7 (5)
on the handle side.
u
Undo the screw
Fig. 7 (6)
and transfer it to the opposite side.
u
Put the cover
Fig. 7 (5)
back on.
u
Screw the turn hinge
Fig. 7 (2)
firmly into place on the new
hinge side (with 4 Nm), possibly using a power screwdriver.
Fig. 8
u
At the top, use a screwdriver to unclip cover
Fig. 8 (7)
and
cover
Fig. 8 (8)
at the front, and remove by pulling out and
down.
u
Unscrew the bearing pin
Fig. 8 (9)
and screw it firmly into
place on the opposite side (with 4 Nm).
u
Refit the cover
Fig. 8 (7)
on the side of the bearing pin: insert
at the back, snap in at the front.
u
Fit the cover
Fig. 8 (8)
on the opposite side: insert at the
back, snap in at the front.
Fig. 9
u
Lift the stopper
Fig. 9 (12)
out of the door bearing bush and
transfer it.
u
Detach door handle, stoppers
Fig. 9 (10)
and pressure
plates
Fig. 9 (11)
and transfer to the opposite side.
u
When mounting the pressure plates, make sure they snap
into place properly.
u
Transfer the spring clamp
Fig. 10 (20)
: Depress the
latch nose and pull the
spring clamp off over it.
u
Slide the spring clamp into
place on the new hinge
side until it clicks into
place.
u
Pull the bearing pin
Fig. 10 (21)
out of the door
bush and transfer it to the
opposite side together with
the washer. The latch nose
must point to the inner side
of the door, the notch to
the outer side.
Fig. 10
u
Hang the door on the bearing pin
Fig. 8 (9)
at the top.
u
Swing the door in at the bottom and insert the bearing pin
Fig. 10 (21)
into the turn hinge. If necessary, turn the bearing
pin until it snaps into place.
u
Insert the securing screw
Fig. 6 (1)
at the bottom into the
bearing pin and tighten it (with 4 Nm).
Putting into operation
6 * Depending on model and options
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr K 3130-20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr K 3130-20 in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr K 3130-20

Liebherr K 3130-20 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info