Manual Liebherr K 3120 (page 5 of 10) (English)

71726

Zoom out

Zoom in

1/10

Fig. 7

At the top, use a screwdriver to unclip cover

Fig. 7 (7)

and

cover

Fig. 7 (8)

at the front, and remove by pulling out and

down.

Unscrew the bearing pin

Fig. 7 (9)

and screw it firmly into

place on the opposite side (with 4 Nm).

Refit the cover

Fig. 7 (7)

on the side of the bearing pin: insert

at the back, snap in at the front.

Fit the cover

Fig. 7 (8)

on the opposite side: insert at the

back, snap in at the front.

Fig. 8

Lift the stopper

Fig. 8 (12)

out of the door bearing bush and

transfer it.

Detach door handle, stoppers

Fig. 8 (10)

and pressure

plates

Fig. 8 (11)

and transfer to the opposite side.

When mounting the pressure plates, make sure they snap

into place properly.

Transfer the spring clamp

Fig. 9 (20)

: Depress the

latch nose and pull the

spring clamp off over it.

Slide the spring clamp into

place on the new hinge

side until it clicks into

place.

Pull the bearing pin

Fig. 9 (21)

out of the door

bush and transfer it to the

opposite side together with

the washer. The latch

nose must point to the

inner side of the door, the

notch to the outer side.

Fig. 9

Hang the door on the bearing pin

Fig. 7 (9)

at the top.

Swing the door in at the bottom and insert the bearing pin

Fig. 9 (21)

into the turn hinge. If necessary, turn the bearing

pin until it snaps into place.

Insert the securing screw

Fig. 5 (1)

at the bottom into the

bearing pin and tighten it (with 4 Nm).

If necessary, align the door flush with the appliance housing

using the two slots in the turn hinge. To do so, unscrew the

middle screw.

Push the spacer

Fig. 4 (22)

into the bottom right of the door.

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough,

the door may drop out. This may lead to severe injuries. What

is more, the door may not close and therefore the appliance

may fail to cool properly.

Screw on the bearing brackets/bearing pins tightly (4 Nm).

Check all of the screws and retighten if necessary.

4.2 Insertion into a row of kitchen units

For appliances 600 mm wide

Fig. 10

(1) Stack cabinet (3) Kitchen cabinet

(2) Appliance (4) Wall

The appliance can be inserted into a row of kitchen units. To

match the appliance

Fig. 10 (2)

to the height of the row of units,

a suitable stack cabinet

Fig. 10 (1)

can be fitted above the

appliance.

When inserting the appliance into a row of kitchen units (max.

depth 580 mm), the appliance can be installed directly next to

the kitchen unit

Fig. 10 (3)

. The appliance door projects relative

to the front of the kitchen unit by 34 mm at the side and by

50 mm in the middle of the appliance. It can be opened and

closed perfectly as a result.

Important for the ventilation:

At the back of the stack cabinet there has to be a ventilation

duct of at least 50 mm depth throughout the width of the

stack cabinet.

The ventilation space under the ceiling has to be at least

300 cm

The larger the ventilation space, the more energy-saving the

appliance is in operation.

If the appliance is installed with the hinges next to a wall

Fig. 10 (4)

, the distance between appliance and wall has to be

at least 40 mm. This corresponds to the projection of the

handle when the door is open.

Putting into operation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr K 3120 in the language / languages: English as an attachment in your email.

The manual is 1,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr K 3120

Liebherr K 3120 User Manual - Dutch - 8 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr K 3120 Manual

Product: