805415
15
Zoom out
Zoom in
Previous page
1/28
Next page
uChange the air filter every six months.
uConfirm the message with OK.
wThe service interval resets.
wThe air filter guarantees the air quality in the fridge.
Activating the setting
uActivating/deactivating (see 6.2 Control concept) .
Reset
This function resets all settings to the factory settings. All
settings that you have made thus far will be reset to their
original values.
Activating the setting
uActivate (see 6.2 Control concept) .
6.4 Fault messages
Fault messages appear in the display. There are two catego‐
ries of fault message:
Category Meaning
Message Reminder of general procedures. You can carry
out these procedures to eliminate the message.
Warning Appears when there are malfunctions. A signal
sounds in addition to the display. The signal
becomes louder until you acknowledge by
tapping the display. You can eliminate simple
defects yourself. For more serious defects, you
must contact customer service.
6.4.1 Warnings
Close the door
This message appears if the door is open for too long.
You can set how long it takes for this message to appear .
uStop alarm: Confirm the message.
-or-
uClose the door.
Power cut
This message appears if the freezer temperature increased
due to a power cut. After the power is restored, the appli‐
ance continues to work at the set temperature.
uStop alarm: Confirm the message.
wTemperature alert appears (see Temperature alarm) .
Temperature alarm
This message appears if the freezer temperature does not
match the set temperature.
Variations in temperature could be because:
-Hot, fresh food was inserted.
-Too much warm room air flowed in when rearranging and
removing food.
-The power was cut off for a while.
-The appliance is faulty.
When the fault is eliminated the appliance continues to
work at the set temperature.
uConfirm the display.
wThe highest temperature is shown.
uConfirm display again.
wThe status display is displayed.
wThe current temperature is shown.
Error
This message appears if there is a fault with the appliance.
An appliance component indicates a fault.
uOpen the door.
uNote down the fault code.
uConfirm the message.
wThe signal tone stops.
wThe status display appears.
uClose the door.
uContact customer service. (see 9.4 Customer Services)
6.4.2 Message
Water tank
This message appears if there is not enough water in the
water tank.
uFill the water tank.
wThe IceMaker produces ice cubes.
uWhen the water tank is full and the following message
appears: Check if the float is stuck.
uIf necessary, drain the water and release the float with a
thin object such as a cotton bud.
uWhen the water tank is full and the following message
appears: Contact customer service. (see 9.4 Customer
Services)
Insert IceMaker drawer*
This message appears if the IceMaker drawer is open.
uPush in the IceMaker drawer.
wThe message disappears.
wThe IceMaker produces ice cubes.
6.4.3 DemoMode
If “D” appears on the display, demo mode is on. This option
is designed for retailers, as it turns off all the cooling func‐
tions.
Stopping DemoMode
If you see the following running in the display:
uConfirm the display within the countdown.
wDemoMode is off.
If the timer is not running:
uUnplug the appliance.
uPlug the appliance in again.
wDemoMode is off.
7 Features
7.1 Door rack
7.1.1 Move/remove the door rack
Fig. 21
uSlide the rack upwards.
uPull forwards.
Features
* Depending on model and options 15
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr ICNc 5123 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr ICNc 5123 in the language / languages: English as an attachment in your email.

The manual is 4.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr ICNc 5123

Liebherr ICNc 5123 User Manual - German - 30 pages

Liebherr ICNc 5123 User Manual - Dutch - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info