561380

Liebherr GP 1213 Comfort Manual

7
Zoom out
Zoom in
Previous page
1/12
Next page
4.6 Connecting the appliance
NOTICE
Failure to connect properly
Damage to the electronics.
u
Do not use a standalone inverter.
u
Do not use an energy saving plug.
WARNING
Failure to connect properly
Fire hazard.
u
Do not use an extension cable.
u
Do not use distributor blocks.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It
must be outside the area of the rear of the appliance.
u
Check the electrical connection.
u
Plug in the power plug.
4.7 Switching on the appliance
u
Press the On/Off button
Fig. 3 (1)
.
w
The appliance is switched on. The temperature display and
Alarm symbol
Fig. 3 (7)
flash until the temperature is cold
enough.
w
If “DEMO” is displayed, demo mode is activated. Please
contact the after sales service.
5 Control
5.1 Brightness of the temperature
display
You can adjust the brightness of the temperature display to the
light conditions of the room in which the appliance is installed.
5.1.1 Adjusting the brightness
The backlight can either be switched off or set to one of 5
levels. The backlight is switched off ex works.
u
To activate the setting mode: Press the SuperFrost button
Fig. 3 (4)
for about 5 seconds.
w
The menu symbol
Fig. 3 (6)
shines and the child lock symbol
Fig. 3 (9)
flashes.
u
Press the setting button
Fig. 3 (2)
to select the brightness
function.
w
The child lock symbol
Fig. 3 (9)
goes out and the brightness
symbol
Fig. 3 (8)
flashes.
u
To confirm: Briefly press the SuperFrost button
Fig. 3 (4)
.
w
The brightness symbol
Fig. 3 (8)
shines.
u
Using the setting button
Fig. 3 (2)
, select either "off" or the
brightness wanted. The more display fields of the tempera-
ture display that light up, the brighter it is. If no field is lit up, it
means "off".
u
To confirm: Press the SuperFrost button
Fig. 3 (4)
.
w
The brightness symbol
Fig. 3 (8)
flashes.
w
The brightness is adjusted to the new value.
u
To deactivate the setting mode: Press the On/Off button
Fig. 3 (1)
.
-or-
u
Wait for 5 minutes.
w
The brightness symbol
Fig. 3 (8)
and the menu symbol
Fig. 3 (6)
go out.
w
The temperature is indicated again in the temperature
display.
5.2 Child proofing
The child-proofing function enables you to make
sure that the appliance is not inadvertently switched
off by playing children.
5.2.1 To activate child lock
u
To activate the setting mode: Press the SuperFrost button
Fig. 3 (4)
for about 5 seconds.
w
The menu symbol
Fig. 3 (6)
shines and the child lock symbol
Fig. 3 (9)
flashes.
u
Briefly press the SuperFrost button
Fig. 3 (4)
to select the
child lock function.
w
The child lock symbol
Fig. 3 (9)
shines. The
-15 °C and -21 °C LEDs shine in the temperature
display.
u
Briefly press the SuperFrost button
Fig. 3 (4)
to activate the
child lock.
w
The child lock symbol
Fig. 3 (9)
flashes. The -15 °C and
-21 °C LEDs go out.
u
To deactivate the setting mode: Press the On/Off button
Fig. 3 (1)
.
-or-
u
Wait for 5 minutes.
w
The menu symbol
Fig. 3 (6)
goes out and the temperature is
displayed again in the temperature display. The child lock
symbol
Fig. 3 (9)
shines.
5.2.2 To deactivate child lock
u
To activate the setting mode: Press the SuperFrost button
Fig. 3 (4)
for about 5 seconds.
w
The menu symbol
Fig. 3 (6)
shines and the child lock symbol
Fig. 3 (9)
flashes.
u
Briefly press the SuperFrost button
Fig. 3 (4)
to select the
child lock function.
w
The child lock symbol
Fig. 3 (9)
shines. The
-18 °C LED shines in the temperature display.
u
Briefly press the SuperFrost button
Fig. 3 (4)
to deactivate
the child lock.
w
The child lock symbol
Fig. 3 (9)
flashes.
u
To deactivate the setting mode: Press the On/Off button
Fig. 3 (1)
.
-or-
u
Wait for 5 minutes.
w
The menu symbol
Fig. 3 (6)
goes out and the temperature is
displayed again in the temperature display. The child lock
symbol
Fig. 3 (9)
no longer shines.
5.3 Temperature alarm
The temperature display and the alarm symbol
Fig. 3 (7)
flash at the same time.
The cause of the temperature being too high may be:
-
warm fresh food was placed inside
Control
* Depending on model and options 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr GP 1213 Comfort at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr GP 1213 Comfort in the language / languages: English as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr GP 1213 Comfort

Liebherr GP 1213 Comfort User Manual - German - 12 pages

Liebherr GP 1213 Comfort User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info