710260

Liebherr GNP 2713-23 Manual

8
Zoom out
Zoom in
Previous page
1/14
Next page
When installing with kitchen units (max. depth 580 mm), the
appliance can be positioned directly next to the kitchen cabinet
Fig. 10 (3)
. The appliance will project by 34 mm
x
at the sides
and 50 mm
x
in the centre of the appliance in relation to the
kitchen cabinet front.
NOTICE
Danger of overheating due to insufficient air ventilation!
The compressor may be damaged if there is insufficient air
ventilation.
u
Take care to ensure adequate air ventilation.
u
Observe the ventilation requirements.
Ventilation requirements:
-
At the back of the stack cabinet there has to be a ventilation
duct of at least 50 mm depth throughout the width of the
stack cabinet.
-
The cross section of the ventilation gap below the ceiling
must be at least 300 cm
2
.
-
the larger the ventilation space, the more energy-saving the
appliance is in operation.
If the appliance is installed with the hinges next to a wall
Fig. 10 (4)
, the distance between appliance and wall has to be
at least 40 mm. This corresponds to the projection of the
handle when the door is open.
4.5 Disposing of packaging
WARNING
Danger of suffocation due to packing material and plastic film!
u
Do not allow children to play with packing material.
The packaging is made of recyclable materials:
-
corrugated board/cardboard
-
expanded polystyrene parts
-
polythene bags and sheets
-
polypropylene straps
-
nailed wooden frame with polyethylene panel*
u
Take the packaging material to an official collecting point.
4.6 Connecting the appliance
NOTICE
Failure to connect properly
Damage to the electronics.
u
Do not use a standalone inverter.
u
Do not use an energy saving plug.
WARNING
Failure to connect properly
Fire hazard.
u
Do not use an extension cable.
u
Do not use distributor blocks.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see 1 Appliance at a glance) .
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It
must be outside the area of the rear of the appliance.
u
Check the electrical connection.
u
Plug in the power plug.
4.7 Switching on the appliance
u
Press the On/Off button
Fig. 3 (1)
.
w
The appliance is switched on. The temperature display and
Alarm symbol
Fig. 3 (10)
flash until the temperature is cold
enough.
w
If “DEMO” is displayed, demo mode is activated. Please
contact the after sales service.
5 Control
5.1 Brightness of the temperature
display
You can adjust the brightness of the temperature display to the
light conditions of the room in which the appliance is installed.
5.1.1 Adjusting the brightness
The background lighting can either be turned off or set to one
of 5 levels. The factory setting is that the background lighting is
turned off.
u
To activate the setting mode: Press the SuperFrost button
Fig. 3 (2)
for about 5 seconds.
w
The menu symbol
Fig. 3 (9)
shines and the child lock symbol
Fig. 3 (8)
flashes.
u
Press the setting button
Fig. 3 (6)
to select the brightness
function.
w
The child lock symbol
Fig. 3 (8)
turns off and the brightness
symbol
Fig. 3 (3)
flashes.
u
To confirm: Briefly press the SuperFrost button
Fig. 3 (2)
.
w
The brightness symbol
Fig. 3 (3)
shines.
u
Using the setting button
Fig. 3 (6)
, select either "off" or the
brightness wanted. The more display fields of the tempera-
ture display that light up, the brighter it is. If no field is lit up, it
means "off".
u
To confirm: Press the SuperFrost button
Fig. 3 (2)
.
w
The brightness symbol
Fig. 3 (3)
flashes.
w
The brightness is adjusted to the new value.
u
To deactivate the setting mode: Press the On/Off button
Fig. 3 (1)
.
-or-
u
Wait for 5 minutes.
w
The brightness symbol
Fig. 3 (3)
and the menu symbol
Fig. 3 (9)
go out.
w
The temperature is indicated again in the temperature
display.
5.2 Child proofing
The child-proofing function enables you to make
sure that the appliance is not inadvertently switched
off by playing children.
5.2.1 To activate child lock
u
To activate the setting mode: Press the SuperFrost button
Fig. 3 (2)
for about 5 seconds.
w
The menu symbol
Fig. 3 (9)
shines and the child lock symbol
Fig. 3 (8)
flashes.
u
Briefly press the SuperFrost button
Fig. 3 (2)
to select the
child lock function.
w
The child lock symbol
Fig. 3 (8)
shines. The
-15 °C and -21 °C LEDs shine in the temperature
display.
Control
8 * Depending on model and options
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr GNP 2713-23 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr GNP 2713-23 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr GNP 2713-23

Liebherr GNP 2713-23 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info