715348

Liebherr CUfb 2831 Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
u
Align the appliance so that it
stands firmly and on a level by
applying the accompanying
spanner to the adjustable-
height feet (A) and using a
spirit level.
u
Then support the door:
Extend the adjustable foot at
the turn hinge (B) until it rests
on the floor and then make a
further 90° turn.
Note
u
Clean the appliance (see 6.2 Cleaning the appliance) .
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
u
Always see to good ventilation at the installation site.
4.3 Changing over the door hinges
You can change over the door hinges if necessary.
Ensure that the following tools are to hand:
q
Torx® 15
q
Torx® 25
q
Screwdriver
q
Cordless screwdriver, if necessary
q
Second person for fitting work, if needed
4.3.1 Detaching the upper door
Note
u
Remove any food from the door racks before removing the
door, so that no food falls out.
Fig. 5
u
Pull off the cover
Fig. 5 (1)
forwards and upwards.
u
Lift off the cover
Fig. 5 (2)
.
CAUTION
Risk of injury if the door tips!
u
Take good hold of the door.
u
Set down the door carefully.
u
Unscrew the upper turn hinge
Fig. 5 (3)
(2x Torx® 25)
Fig. 5 (4)
and lift it off.
u
Lift up the upper door and set it aside.
4.3.2 Detaching the lower door
u
Open the lower door.
CAUTION
Risk of injury if the door tips!
u
Take good hold of the door.
u
Set down the door carefully.
u
Unscrew the fastening screws
Fig. 6 (11)
(2 x Torx® 25) and
pull the centre bearing block out of the lower door.
u
Remove plastic washer
Fig. 6 (10)
.
u
Lift up the door and set it aside.
4.3.3 Transferring the middle bearing elements
Fig. 6
u
Remove the cover
Fig. 6 (12)
carefully.
u
Re-install the cover
Fig. 6 (12)
on the opposite side.
4.3.4 Transferring the lower bearing elements
Fig. 7
u
Unscrew fastening screws
Fig. 7 (21)
.
u
Remove the lower bearing block
Fig. 7 (23)
, complete with
bearing bolt
Fig. 7 (24)
, washer
Fig. 7 (26)
and adjustable
foot
Fig. 7 (22)
.
u
Unscrew the bearing bolt
Fig. 7 (24)
, complete with washer
Fig. 7 (26)
, re-locate it into the mounting hole on the oppo-
site side of the bearing block and tighten again.
u
Carefully remove the cover plate
Fig. 7 (25)
and re-locate it
to the other side.
u
Fasten the lower bearing block
Fig. 7 (23)
, complete with
bearing bolt
Fig. 7 (24)
, washer
Fig. 7 (26)
and adjustable
foot
Fig. 7 (22)
to the new hinge side, with the help of a cord-
less screwdriver if necessary, and tighten (with 4 Nm)
once again.
4.3.5 Fitting the lower door
u
Lower the bottom door onto the bearing bolt
Fig. 7 (24)
.
u
Close the door.
u
Insert the centre bearing block
Fig. 6 (13)
turned through
180° into the lower door and fasten firmly (with 4 Nm)to the
new hinge side with the fastening screws(2 x Torx® 25).
u
Refit plastic washer
Fig. 6 (10)
.
Putting into operation
6 * Depending on model and options
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr CUfb 2831 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr CUfb 2831 in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr CUfb 2831

Liebherr CUfb 2831 User Manual - German - 14 pages

Liebherr CUfb 2831 User Manual - Dutch - 14 pages

Liebherr CUfb 2831 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info