597399

Liebherr CTNesf 3663 Premium Manual

7
Zoom out
Zoom in
Previous page
1/16
Next page
4.3.4 Transferring the lower bearing elements
Fig. 7
u
Lift out the bearing pin
Fig. 7 (22)
together with washer
Fig. 7 (23)
and foot
Fig. 7 (24)
.
u
Lift off the stopper
Fig. 7 (21)
.
u
Unscrew
Fig. 7 (26)
the turn hinge
Fig. 7 (25)
.
u
Unscrew
Fig. 7 (29)
the bearing element
Fig. 7 (28)
, transfer
it to the opposite location hole of the turn hinge and screw it
firmly into place.
u
Carefully lift off the cover on the handle side
Fig. 7 (27)
and
transfer it to the opposite side.
u
Screw the turn hinge
Fig. 7 (25)
firmly into place on the new
hinge side, possibly using a cordless screwdriver (with
4 Nm).
u
Re-insert the stopper
Fig. 7 (21)
into the other hole.
u
Re-insert the bearing pin
Fig. 7 (22)
together with washer
and foot. In so doing, pay attention that the locating lug
points backwards
4.3.5 Transferring the handles
On both the upper and lower door:
u
Transfer the spring clamp
Fig. 8 (31)
: Depress the
latch nose and pull the
spring clamp off over it.
u
Slide the spring clamp
into place on the new
hinge side until it clicks
into place.
Fig. 8
Fig. 9
u
Lift the stopper
Fig. 9 (30)
out of the door bearing bush and
transfer it.
u
Detach door handle
Fig. 9 (32)
, stopper
Fig. 9 (33)
and pres-
sure plates
Fig. 9 (34)
and transfer to the opposite side.
u
When fitting the pressure plates on the opposite side, make
sure they snap properly into place*
4.3.6 Fitting the lower door
u
Place the lower door from above onto the lower bearing pin
Fig. 7 (22)
.
u
Close the door.
u
Place the plastic cap
Fig. 6 (10)
back onto the middle turn
hinge
Fig. 6 (13)
.
u
Place the middle bearing pin
Fig. 6 (11)
in the lower door, on
the new hinge side, through the middle turn hinge
Fig. 6 (13)
.
4.3.7 Fitting the upper door
u
Place the upper door on the middle bearing pin
Fig. 6 (11)
.
u
Insert the upper turn hinge
Fig. 5 (3)
in the door on the new
hinge side.
u
Screw the upper turn hinge firmly into place (with 4 Nm)
(2x Torx® 25)
Fig. 5 (4)
. Possibly make preliminary holes
with a bradawl or use a cordless screwdriver.
u
Apply the cover
Fig. 5 (1)
and cover
Fig. 5 (2)
to the opposite
side from the outside and snap them into place.
4.3.8 Aligning the doors
u
If necessary, align the doors to the appliance housing by
way of the two oblong holes in the bottom turn hinge
Fig. 7 (25)
and middle turn hinge
Fig. 6 (13)
. To do so,
unscrew the middle screw in the bottom turn hinge
Fig. 7 (25)
.
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly enough,
the door may drop out. This may lead to severe injuries. What is
more, the door may not close and therefore the appliance may
fail to cool properly.
u
Screw the turn hinges firmly into place with 4 Nm.
u
Check all of the screws and retighten if necessary.
4.4 Insertion into a row of kitchen units
Fig. 10
(1) Stack cabinet (3) Kitchen cabinet
(2) Appliance (4) Wall
Putting into operation
* Depending on model and options 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr CTNesf 3663 Premium at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr CTNesf 3663 Premium in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr CTNesf 3663 Premium

Liebherr CTNesf 3663 Premium User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info