715319

Liebherr CNkw 4313 Manual

5
Zoom out
Zoom in
Previous page
1/11
Next page
5
Putting into operation
* according to model and design
4.4 Insertion into a row of kitchen units
The appliance can be tted into kitchen units.
u see assembly instructions provided.
Ventilation requirements:
A [mm] B [mm] C [cm
2
] D [mm] E [mm]
655
x
75 min. 300 min. 50 min. 19
x
This dimension increases by 35 mm in case of appliances with
wall spacer brackets attached (see 4.2).
The appliance may protrude further, depending on the depth of
the kitchen units and the use of wall spacer brackets.
ATTENTION
Risk of damage to the appliance due to overheating with
insucient ventilation!
The compressor may be damaged with insucient ventilation.
u Ensure sucient ventilation.
u Observe the ventilation requirements.
4.5 Disposing of packaging
WARNING
Danger of suocation due to packing material and
plastic lm!
u Do not allow children to play with packaging material.
The packaging is made of recyclable materials:
- corrugated board/cardboard
- expanded polystyrene parts
- polythene bags and sheets
- polypropylene straps
- nailed wooden frame with polyethylene panel*
u Take the packaging material to an ocial collecting point.
4.6 Connecting the appliance
NOTICE
Failure to connect properly
Damage to the electronics.
u Do not use a standalone inverter.
u Do not use an energy saving plug.
WARNING
Failure to connect properly Fire.
u Do not use an extension cable.
u Do not use distributor blocks.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It must
be outside the area of the rear of the appliance.
u Check the electrical connection.
u Plug in the power plug.
4.7 Switching on the appliance
Note
u To switch on the entire appliance it is necessary only to switch
on the freezer compartment. In so doing, the refrigerator
compartment is automatically switched on as well.
The appliance should have been operating for about 2 hours
before you stock it with frozen food. Only place frozen goods in
the freeze compartment once the temperature display shows at
least -18°C.
q Do not install the appliance in a location where it is exposed to
direct radiation of the sun, next to a cooker, heater and similar.
q Always stand the appliance backed directly to the wall using
the enclosed wall spacers (see below).
q The appliance may be moved only when it is empty.
q The surface supporting the appliance must be at the same
level as the surrounding oor.
q Do not install the appliance without assistance.
q The more coolant there is in the appliance, the larger the
room in which the appliance is installed must be. If the room
is too small, any leak may create a ammable mixture of gas
and air. For each 8 g of coolant the installation space must
be at least 1 m3. Information on the coolant is on the model
plate inside the appliance.
u Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because
otherwise there will be vibratory noise!
u Remove the protective lm from the outside of the appliance.*
u Remove all transit supports.
The spacers supplied with some appliances must be used to
achieve the stated energy consumption. These will extend the
depth of the appliance by approx. 35 mm. The appliance is fully
functional if the spacers are not used, but does have a slightly
higher energy consumption.
u
Fig. 9 In the case of an appliance with enclosed wall spacers,
mount the wall spacers on the back of the appliance at the top
left and right.
u Dispose of packaging material. (see 4.5)
u Fig. 4
Align the appliance so that it stands firmly and on a
level by applying the accompanying spanner to the adjustable-
height feet (A) and using a spirit level. Then support the door:
Extend the adjustable foot at the turn hinge (B) until it rests on
the oor and then make a further 90° turn.
Note
u Clean the appliance (see 6.2).
If the appliance is installed in a very damp environment, conden-
sate may form on the outside of the appliance.
u Always see to good ventilation at the installation site.
4.3 Changing over the door hinges
You can change over the door hinges if necessary:
u see assembly instructions provided.
Ensure that the following tools are to hand:
q Torx® 25
q Screwdriver
q Cordless screwdriver, if necessary
q Second person for tting work, if needed
Note
u Remove any food from the door racks before removing the
door, so that no food falls out.
CAUTION
Risk of injury if the door tips!
u Take good hold of the door.
u Set down the door carefully.
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place rmly enough,
the door may drop out. This may lead to severe injuries. What is
more, the door may not close and therefore the appliance may
fail to cool properly.
u Screw the turn hinges rmly into place with 4 Nm.
u Check all of the screws and retighten if necessary.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr CNkw 4313 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr CNkw 4313 in the language / languages: English as an attachment in your email.

The manual is 1,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr CNkw 4313

Liebherr CNkw 4313 User Manual - German - 10 pages

Liebherr CNkw 4313 User Manual - Dutch - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info