597566
4
Zoom out
Zoom in
Previous page
1/5
Next page
8
Wall mounting
The appliance can be wall-mounted.
There are two mounting holes
at the top of the back of the
appliance.
Make sure the wall and the
fasteners can withstand the
weight of the appliance when
fully loaded.
Inserting the grid shelves
The knurled screws supplied are used
to support the grid shelves.
Screw the knurled screws into
the desired position inside the
appliance to the left and right
and insert the grid shelves.
The lower grid shelf only
requires two screws at the
front. The rear part of this grid
shelf rests on the ledge of the
interior container.
Electrical connection
Only operate the appliance with alternating current (AC).
The permissible voltage and frequency are indicated on the type
plate. The position of the type plate is shown in the section entitled
Description of the appliance.
The socket must be properly earthed and protected by a fuse.
The tripping current of the fuse must be between 10 A and 16 A.
The socket must not be situated behind the appliance and must
be easily accessible.
Do not connect the appliance using an exten-
sion cable or extension socket.
Do not use stand-alone inverters (conversion
of direct current to alternating/three-phase
current) or energy-saving plugs. Risk of dam-
age to the electronic control system!
Setting the temperature
Set the temperature inside the ap-
pliance using the temperature
control.
When the control is turned to
"7", the temperature inside the
appliance is at its lowest.
Set the control between "1" and
"7" as required.
Appliance
dimensions
Setting up
• Avoidpositioningtheapplianceindirectsunlightornearcook-
ers, radiators and similar sources of heat.
• Theflooronwhichtheappliancestandsshouldbehorizontal
and level. Compensate for uneven floors with the adjustable
feet.
• StandardEN378specifiesthattheroominwhichyouinstall
your appliance must have a volume of 1 m
3
per8gofR600a
refrigerant used in the appliance, so as to avoid the formation of
inflammable gas/air mixtures in the room where the appliance
is located in the event of a leak in the refrigerant circuit. The
quantity of refrigerant used in your appliance is indicated on
the type plate on the inside of the appliance.
• Theremustbeagapofatleast20cmbetweentheupperedge
of the appliance and the ceiling. Always ensure that there is good
ventilation and that the outward flowing air is able to escape.
Do not cover ventilation
openings or grille.
Switching the appliance on and off
You are recommended to clean the interior of the appliance before
switching it on for the first time (see Cleaning).
Switching the appliance on
Connect the appliance to the mains - the appliance is switched on.
Important
Once the mains plug has been inserted, the refrigeration
unit may not come on until up to 8 minutes later. This is
required to protect the electronic controls.
Switching the appliance o
Pulloutthemainsplugorsetthetemperaturecontrol
to 0.
Important
When the temperature control is turned to "0", the refrig-
eration system is switched off, but the appliance is not
completely disconnected from the mains. Before cleaning,
always disconnect the appliance from the mains. Remove
the plug.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr CMes 502 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr CMes 502 in the language / languages: English as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr CMes 502

Liebherr CMes 502 User Manual - German - 5 pages

Liebherr CMes 502 User Manual - Dutch - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info