612047

Liebherr CBNPes 3976 Manual

8
Zoom out
Zoom in
Previous page
1/20
Next page
u
On the bottom door: Lift the stopper
Fig. 10 (70)
out of the
door bearing bush and transfer it.
u
On both doors: Detach door handle
Fig. 10 (72)
, stopper
Fig. 10 (73)
and pressure plates
Fig. 10 (74)
and transfer to
the opposite side.
u
When fitting the pressure plates on the opposite side, make
sure they snap properly into place.*
4.3.7 Fitting the lower door
u
Place the door from above onto the bearing pin
Fig. 8 (52)
.
u
Close the door.
u
Place the plastic cap
Fig. 7 (40)
back on the middle turn
hinge
Fig. 7 (42)
u
Pass the middle bearing pin
Fig. 7 (41)
through the middle
turn hinge
Fig. 7 (42)
into the lower door.
4.3.8 Transferring the cable connection (upper
door)
Fig. 11
u
Using a screwdriver, disengage the cover
Fig. 11 (63)
from
the door.
u
Detach the connector
Fig. 11 (60)
.
u
On the upper door, rotate the turn hinge
Fig. 11 (23)
outwards, parallel to the edge of the door.
Fig. 12
NOTICE
Cables may be twisted and damaged as a result!
u
Use the template.
u
Detach the supplied template
Fig. 12 (61)
from the turn
hinge and use it to prevent the turn hinge
Fig. 12 (23)
and
bush from turning.
u
Using a screwdriver, push out the turn
hinge
Fig. 11 (23)
from underneath and
remove it from the door, complete with
cable.
u
Using a screwdriver, push out the stopper
Fig. 11 (62)
from underneath and transfer it
to the opposite side.
u
Thread in the cable of the turn hinge
Fig. 11 (23)
on the
opposite side and insert the turn hinge.
u
Detach the template
Fig. 11 (61)
and secure it in the turn
hinge.
u
Plug in the connector
Fig. 11 (60)
.
u
Lay the cable in the guide.
u
Snap the cover
Fig. 11 (63)
into place on the door.
4.3.9 Fitting the upper door
u
Place the upper door on the middle bearing pin
Fig. 7 (41)
,
close the door and attach the upper turn hinge
Fig. 6 (23)
so
that it engages in the upper side of the appliance.
u
Screw theturn hinge
Fig. 6 (23)
firmly into place (with
4 Nm). Possibly make preliminary holes with a bradawl or
use a cordless screwdriver.
u
Snap cover
Fig. 6 (20)
and cover
Fig. 6 (21)
into place.
u
Plug in the connector
Fig. 4 (12)
again.
u
Lay the cable in the guide.
u
Attach the cover
Fig. 4 (10)
again.
u
Turn the cover
Fig. 5 (6)
through 180°, attach it from the
outside to the handle side and snap it into place.
4.3.10 Aligning the doors
u
Possibly align the door to the appliance housing by way of
the two slots in the lower turn hinge
Fig. 8 (55)
and middle
turn hinge
Fig. 7 (42)
. To do so, unscrew the middle screw in
the bottom turn hinge
Fig. 8 (55)
.
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly enough,
the door may drop out. This may lead to severe injuries. What
is more, the door may not close and therefore the appliance
may fail to cool properly.
u
Screw the turn hinges firmly into place with 4 Nm.
u
Check all of the screws and retighten if necessary.
4.4 Insertion into a row of kitchen units
Fig. 13
(1) Stack cabinet (3) Kitchen cabinet
(2) Appliance (4) Wall
Putting into operation
8 * Depending on model and options
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr CBNPes 3976 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr CBNPes 3976 in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr CBNPes 3976

Liebherr CBNPes 3976 User Manual - German - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info