Manual Liebherr CBNES 3967 (page 10 of 26) (English)

76953

Zoom out

Zoom in

1/26

Unscrew

Fig. 15 (56)

the turn hinge

Fig. 15 (55)

Unscrew the bearing element

Fig. 15 (58)

, turn it through

180° and screw it firmly into place again inside.

Carefully lift off the cover on the handle side

Fig. 15 (57)

and

transfer it to the opposite side.

Screw the bottom turn hinge

Fig. 15 (55)

firmly into place

(with 4 Nm) on the new hinge side, possibly using a cord-

less screwdriver.

Re-insert the stopper

Fig. 15 (51)

into the other hole.

Re-insert the bearing pin

Fig. 15 (52)

together with the

washer and adjustable-height foot. In so doing, pay attention

that the locating lug points backwards

4.3.9 Transferring the handles

For appliances without soft stop mechanism (on both

doors):

Transfer the spring clamp

Fig. 16 (71)

: Depress the

latch nose and pull the

spring clamp off over it.

Slide the spring clamp into

place on the new hinge

side until it clicks into

place.

Fig. 16

For all appliances:

Fig. 17

On the bottom door: Lift the stopper

Fig. 17 (70)

out of the

door bearing bush and transfer it.

On both doors: Detach door handle

Fig. 17 (72)

, stopper

Fig. 17 (73)

and pressure plates

Fig. 17 (74)

and transfer to

the opposite side.

When fitting the pressure plates on the opposite side, make

sure they snap properly into place.*

4.3.10 Fitting the lower door

Place the door from above onto the bearing pin

Fig. 15 (52)

Close the door.

Place the plastic cap

Fig. 13 (40)

back on the middle turn

hinge

Fig. 13 (42)

Pass the middle bearing pin

Fig. 13 (41)

through the middle

turn hinge

Fig. 13 (42)

into the lower door.

Appliances with soft stop mechanism:

Attach the washer

Fig. 13 (44)

to the middle bearing pin

Fig. 13 (41)

4.3.11 Fitting the lower soft stop mechanism*

For appliances with soft stop mechanism.

For appliances without soft stop mechanism proceed with

item (see 4.3.12) .

Fig. 18

Remove the cover

Fig. 18 (36)

from the faceplate

Fig. 18 (30)

and re-insert it at the other side.

Engage the joint of the soft stop unit on the hinge side (A)

and swing it into place (B).

The screw holes at the left and right have to register.

Screw the soft stop unit firmly into place(2x Torx® 15)

Fig. 18 (35)

Fig. 19

Attach the faceplate

Fig. 19 (30)

to the soft stop bracket so

that the catches face forwards and the front faces the appli-

ance.

Draw the soft stop bracket

Fig. 19 (34)

to the bearing

element

Fig. 19 (56)

and insert the pin

Fig. 19 (33)

from

above so that the square is seated in the depression.

Attach and engage the cover

Fig. 19 (31)

Pay attention that the cover fits properly so that the door

closes properly and the pin is secured.

Twist the safety lock

Fig. 19 (32)

for removal.

Snap thefaceplate

Fig. 19 (30)

onto the door.

Close the lower door.

4.3.12 Transferring the cable connection

(upper door)

Fig. 20

Using a screwdriver, disengage the cover

Fig. 20 (63)

from

the door.

Detach the connector

Fig. 20 (60)

Putting into operation

10 * Depending on model and options

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr CBNES 3967 in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr CBNES 3967

Liebherr CBNES 3967 User Manual - German - 26 pages

Liebherr CBNES 3967 User Manual - Dutch - 5 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr CBNES 3967 Manual

Product: