Manual Liebherr CBNES 3857 (page 11 of 26) (English)

69681

Zoom out

Zoom in

1/26

On the upper door, rotate the turn hinge

Fig. 20 (23)

outwards, parallel to the edge of the door.

Fig. 21

NOTICE

Cables may be twisted and damaged as a result!

Use the template.

Detach the supplied template

Fig. 21 (61)

from the turn

hinge and use it to prevent the turn hinge

Fig. 21 (23)

and

bush from turning.

Using a screwdriver, push out the turn

hinge

Fig. 20 (23)

from underneath and

remove it from the door, complete with

cable.

Using a screwdriver, push out the stopper

Fig. 20 (62)

from underneath and transfer it

to the opposite side.

Thread in the cable of the turn hinge

Fig. 20 (23)

on the

opposite side and insert the turn hinge.

Detach the template

Fig. 20 (61)

and secure it in the turn

hinge.

Plug in the connector

Fig. 20 (60)

Lay the cable in the guide.

Appliances without soft stop mechanism:

Snap the cover

Fig. 20 (63)

into place on the door.

4.3.13 Fitting the upper door

Place the upper door on the middle bearing pin

Fig. 13 (41)

close the door and attach the upper turn hinge

Fig. 10 (23)

so that it engages in the upper side of the appliance.

Screw theturn hinge

Fig. 10 (23)

firmly into place (with

4 Nm). Possibly make preliminary holes with a bradawl or

use a cordless screwdriver.

Snap cover

Fig. 10 (20)

and cover

Fig. 10 (21)

into place.

Plug in the connector

Fig. 8 (12)

again.

Lay the cable in the guide.

Attach the cover

Fig. 8 (10)

again.

Appliances without soft stop mechanism:

Turn the cover

Fig. 9 (6)

through 180°, attach it from the

outside to the handle side and snap it into place.

Turn the cover

Fig. 9 (11)

through 180°, attach it from the

outside to the handle side and snap it into place.

Appliances with soft stop mechanism:

Leave the door open.

4.3.14 Fitting the upper soft stop mechanism*

For appliances with soft stop mechanism.

For appliances without soft stop mechanism proceed with

item (see 4.3.15) .

Fig. 22

Remove the cover

Fig. 22 (9)

from the faceplate

Fig. 22 (1)

and re-insert it at the other side.

Engage the upper soft stop unit with the joint on the hinge

side (A) and swivel into place (B).

The screw holes at the left and right have to register.

Screw the soft stop unit firmly into place. (2x Torx® 15)

Fig. 22 (7)

Note

Keep to the correct order. First attach the panel over the soft

stop bracket, then the cover.

Fig. 23

Attach the faceplate

Fig. 23 (1)

to the soft stop bracket

Fig. 23 (4)

so that the catches face inwards and the front

faces the appliance.

Slide on the cover

Fig. 23 (5)

from the outside (A) and swivel

it over the bearing element

Fig. 23 (8)

(B).

Attach the cover

Fig. 23 (5)

and engage it as far as the first

detent.

The openings for the pin are on top of one another after the

soft stop bracket has been positioned.

Draw the soft stop bracket

Fig. 23 (4)

to the bearing element

Fig. 23 (8)

and insert the pin

Fig. 23 (4)

from above so that

the square is seated in the depression.

Now completely snap the cover

Fig. 23 (5)

onto the bearing

element

Fig. 23 (8)

Pay attention that the cover fits properly so that the door

closes properly and the pin is secured.

Twist the safety lock

Fig. 23 (2)

for removal.

Snap thefaceplate

Fig. 23 (1)

onto the door.

Turn the cover

Fig. 6 (6)

through 180°, attach and engage it

on the handle side.

4.3.15 Aligning the doors

Possibly align the door to the appliance housing by way of

the two slots in the lower turn hinge

Fig. 15 (55)

and middle

turn hinge

Fig. 13 (42)

. To do so, unscrew the middle screw

in the bottom turn hinge

Fig. 15 (55)

Putting into operation

* Depending on model and options 11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr CBNES 3857 in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr CBNES 3857

Liebherr CBNES 3857 User Manual - German - 26 pages

Liebherr CBNES 3857 User Manual - Dutch - 13 pages

Liebherr CBNES 3857 User Manual - Dutch - 14 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr CBNES 3857 Manual

Product: