Manual Liebherr CBN3733 (page 7 of 16) (English)

495779

Zoom out

Zoom in

1/16

Screw the turn hinge

Fig. 6 (25)

firmly into place on the new

hinge side, possibly using a cordless screwdriver (with

4 Nm).

Re-insert the stopper

Fig. 6 (21)

into the other hole.

Re-insert the bearing pin

Fig. 6 (22)

together with washer

and foot. In so doing, pay attention that the locating lug

points backwards

4.3.5 Transferring the handles

On both the upper and lower door:

Transfer the spring clamp

Fig. 7 (31)

: Depress the

latch nose and pull the

spring clamp off over it.

Slide the spring clamp

into place on the new

hinge side until it clicks

into place.

Fig. 7

Fig. 8

Lift the stopper

Fig. 8 (30)

out of the door bearing bush and

transfer it.

Detach door handle

Fig. 8 (32)

, stopper

Fig. 8 (33)

and pres-

sure plates

Fig. 8 (34)

and transfer to the opposite side.

When fitting the pressure plates on the opposite side, make

sure they snap properly into place*

4.3.6 Fitting the lower door

Place the lower door from above onto the lower bearing pin

Fig. 6 (22)

Close the door.

Place the plastic cap

Fig. 5 (10)

back onto the middle turn

hinge

Fig. 5 (13)

Place the middle bearing pin

Fig. 5 (11)

in the lower door, on

the new hinge side, through the middle turn hinge

Fig. 5 (13)

4.3.7 Fitting the upper door

Place the upper door on the middle bearing pin

Fig. 5 (11)

Insert the upper turn hinge

Fig. 4 (3)

in the door on the new

hinge side.

Screw the upper turn hinge firmly into place (with 4 Nm)

(2x Torx® 25)

Fig. 4 (4)

. Possibly make preliminary holes

with a bradawl or use a cordless screwdriver.

Apply the cover

Fig. 4 (1)

and cover

Fig. 4 (2)

to the oppo-

site side from the outside and snap them into place.

4.3.8 Aligning the doors

If necessary, align the doors to the appliance housing by

way of the two oblong holes in the bottom turn hinge

Fig. 6 (25)

and middle turn hinge

Fig. 5 (13)

. To do so,

unscrew the middle screw in the bottom turn hinge

Fig. 6 (25)

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough,

the door may drop out. This may lead to severe injuries. What

is more, the door may not close and therefore the appliance

may fail to cool properly.

Screw the turn hinges firmly into place with 4 Nm.

Check all of the screws and retighten if necessary.

4.4 Insertion into a row of kitchen units

Fig. 9

(1) Stack cabinet (3) Kitchen cabinet

(2) Appliance (4) Wall

For appliances supplied with wall spacers, the measurement

increases by 35 mm (see 4.2) .

The appliance can be inserted into a row of kitchen units. To

match the appliance

Fig. 9 (2)

to the height of the row of units,

a suitable stack cabinet

Fig. 9 (1)

can be fitted above the appli-

ance.

When installing with kitchen units (max. depth 580 mm), the

appliance can be positioned directly next to the kitchen cabinet

Fig. 9 (3)

. The appliance will project by 34 mm

at the sides and

50 mm

in the centre of the appliance in relation to the kitchen

cabinet front.

Ventilation requirements:

At the back of the stack cabinet there has to be a ventilation

duct of at least 50 mm depth throughout the width of the

stack cabinet.

The ventilation space under the ceiling has to be at least

300 cm

the larger the ventilation space, the more energy-saving the

appliance is in operation.

If the appliance is installed with the hinges next to a wall

Fig. 9 (4)

, the distance between appliance and wall has to be at

least 40 mm. This corresponds to the projection of the handle

when the door is open.

Putting into operation

* Depending on model and options 7

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr CBN3733 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr CBN3733

Liebherr CBN3733 User Manual - German - 16 pages

Liebherr CBN3733 User Manual - Dutch - 14 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr CBN3733 Manual

Product: