526328

LG VR6170LVM Manual

24
Zoom out
Zoom in
Previous page
1/40
Next page
OWNER’S MANUAL
CLEANING ROBOT
VR6170LVM
Before using, please carefully read the Safety Precautions pages to
allow for safe operation of the product. After reading the operation
manual, please keep it in an easily accessible location.
www.lg.com
FEATURES
Images of the ceiling and floor are obtained from the sensors of the upper
and lower cameras, and through this, the location of Roboking 2.0 will be
confirmed, therefore, elaborate cleaning can be accomplished for every part
of the room.
As the noise levels are at a quiet 60dB(A), cleaning can be performed at
night.
*60dB(A)
Roboking 2.0 memorizes the location for cleaning.
* Minimizes the overlapping of cleaning area
The use of the ultra microfiber mop accessory allows finer dust to be
collected from hard flooring. (option)
The Roboking 2.0 also has voice confirmation and instruction that can be
easily understood by the user.
The Roboking 2.0 has two auto cleaning modes that can be selected by the
user.
*Spatial expantion mode, zigzag mode
Camera sensor
(upper, lower section)
“Please, check
the dust bin.”
CONTENTS
Safety precautions
Included with product
Parts description
Button functions
Display status information
Before you start
Overview
1
BEFORE THE USE
2
METHOD OF USE
3
HANDLING METHOD AFTER USE
29~31
32
How to install the home station
How to turn the Roboking 2.0 power supply on & off
How to start and stop cleaning
How to charge the battery
Cleaning modes
Auxiliary cleaning modes
Timer cleaning
Mop cleaning (option)
Location search function
Cleaning the dust bin
Cleaning the dust bin filter
Cleaning the brush
Cleaning the sensor/charging terminal
Cleaning the side brush
Cleaning the ultra microfiber mop (option)
4
ADDITIONAL INFORMATION
5
REFERENCE
2~4
5
6~7
8~9
10
11
12
13
14
15
16~17
18
19
20
21
22
23
24
25
26
27
28
Troubleshooting
Before you call for service
Product specifications
Open source software notice
33
34
2
SAFETY PRECAUTIONS
The purpose of the safety precautions described below is for the user to use the product safely and
correctly to prevent any unexpected risk of injury or damage.
Basic safety precautions
For your safety, do not remove the
battery from the Roboking 2.0. If you
need to replace the battery or the
Roboking 2.0, take it to the nearest
authorized LG Electronics service
center or dealer for assistance.
Failure to follow this warning can
cause fire or product failure.
Make sure the power cord of the
home station is not crushed under a
heavy object or damaged by contact
with sharp objects.
Failure to follow this warning can
cause electric shock, fire or product
failure. If the power cord is broken,
do not plug it in. Take the product
to an LG Electronics Authorised
service repairer.
Do not place the home station and
the Roboking 2.0 near a heating
device.
Doing so can cause product
deformation, fire, or product failure.
Do not force the power plug to
bend. Do not use the power plug
when it has been damaged or
loosened.
Doing so can cause fire or product
failure.
Never use the Roboking 2.0 with a
battery and/or home station from
any other product than the
Roboking 2.0.
Doing so can cause fire or product
failure.
Do not use the Roboking 2.0 when
candles or fragile objects are placed
on the floor.
Doing so can cause fire or product
failure.
Always use a dedicated outlet with
5A or above.
If multiple appliances are connected
to an outlet simultaneously, they
can generate enough heat to cause
a fire.
When pulling out the power plug,
always pull it out by grabbing the
plug, not the cord. When pulling out
the power plug, do not to touch the
prongs with your fingers.
Doing so can cause an electric
shock.
After reading this manual, please keep it in an easily accessible location.
This is the safety alert symbol. This symbol alerts you to potential hazards that can result in
property damage and/or serious bodily harm or death.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.
WARNING
WARNING
CAUTION
3
SAFETY PRECAUTIONS
Do not touch the power plug with
wet hands.
Doing so can cause electric shock.
Do not spray or suck in inflammable
materials, surfactants, or drinking water
in the vicinity of the Roboking 2.0.
Doing so can cause fire or product
failure.
* Inflammable materials: gasoline,
thinner, etc.
* Surfactant: detergent, articles for
bath, etc.
Do not insert any part of the body,
such as a hand or foot, below the
brush or wheels of the
Roboking 2.0 while in use.
Doing so can cause injury or
product damage.
Do not operate the Roboking 2.0
on narrow and high furniture such
as a wardrobe, refrigerator, desk,
table, etc.
Doing so can cause injury, product
failure or damage which is not
covered by the warranty.
Frequently empty the dust bin and
maintain its cleanliness.
The dust collected in the dust
bin can trigger allergies and may
contain harmful insects.
Use the Roboking 2.0 indoors only.
Using it outdoors can cause product
failure and irreparable damage to
the unit.
Close the cover of the dust bin on
the main unit before start cleaning.
If the cover is not closed, it can
cause injury or product damage.
Do not allow children or pets to play
with or rest upon the Roboking 2.0 at
any time. Do not use the Roboking 2.0
while an object is hanging from it.
Doing so can cause injury or
product damage.
Turn the power supply off
immediately if any abnormal sound,
odor, or smoke is generated from
the Roboking 2.0.
Failure to do so can cause fire or
product failure.
Do not operate the Roboking 2.0 in
a room where a child is sleeping.
Doing so can cause injury or
product damage.
Do not leave Children or pets near
the Roboking 2.0 unsupervised.
Doing so can cause injury or
product damage.
Do not drop the Roboking 2.0 or
subject it to strong impacts.
Doing so can cause injury or
product failure not covered by the
warranty.
Do not expose the Roboking 2.0 to
cold temperatures (less than -5°C)
for a long period of time.
Doing so can cause product failure.
Remove any cable or long string on
the floor.
Cable or string can get tangled in
the wheels of Roboking 2.0 and
cause product failure or the cord to
be disconnected.
Gasoline
Detergent
WARNING
CAUTION
4
SAFETY PRECAUTIONS
Check the following items before use:
• Empty the dust bin after if fills up.
• Remove any cables or long strings from the floor.
• Remove any moisture from the floor before cleaning.
• Close the cover of the dust bin before cleaning.
• Remove fragile or unnecessary objects from the room to be cleaned.
For example, remove expensive ceramics and valuables from the floor.
• Confirm whether the battery has sufficient power, and if it is low, recharge it.
• Close the doors of any room that you do not want the Roboking 2.0 to enter.
During cleaning, the Roboking 2.0 may enter another room and continue cleaning.
• Do not use this product in the room where a child is sleeping alone. The child can be hurt.
• Remove towels, foot towel or any other thin cloth from the floor as they can get caught by the
brush.
• Cleaning will not proceed smoothly on carpets or rugs with tassels or carpets thicker
than 8 mm (0.315 in). It may be more convenient to rearrange or remove them before using
the product.
CAUTION
In rare cases, the Roboking 2.0’s
brush can damage the carpet. If
this happens, immediately stop the
cleaning operation.
When a carpet has long tassels, the
tassels can be damaged.
Do not let the main unit and
charging terminal of the home
station come into contact with
metallic objects.
Doing so can cause product failure.
Do not put water, detergent, etc.
into the Roboking 2.0.
Doing so can cause product failure.
Do not put any water or detergent
on the Roboking 2.0. If liquids get
inside of the Roboking 2.0, turn off
the power supply and contact an LG
Electronics sales agent or customer
care center.
If the floor is wet or has wet spots,
wipe them up before using the
Roboking 2.0. Do not use the
Roboking 2.0 on a wet surface.
Failure to do so can cause product
failure.
When attaching the mop, do not
block the bottom camera sensor.
Blocking the bottom camera sensor
may not allow the product to work
smoothly.
Do not allow the Roboking 2.0 to
sweep up liquids, blades, thumb
tacks, hot ashes, wooden shavings
etc.
These items can cause product
failure.
Do not put sharp objects into the
opening of the Roboking 2.0’s
supersonic sensor.
Doing so can cause product failure.
Do not use the Roboking 2.0 when
the dust bin is completely filled up.
Doing so can cause product failure.
When the robot cleaner is
operating, it may hit the chair leg,
desk leg, table leg or other narrow
pieces of furniture.
For quicker and better cleaning,
place the dining chairs on top of the
dining table.
Tip
5
INCLUDED WITH PRODUCT
 Figures can be different from actual objects.
Dust bin filter (spare)
Brush for cleaning filter Mop plate Ultra microfiber mop
(2 pieces) (option)
Dry cell for
remote controller
(2 units of AAA size)
Quick guide
Operation manual
Home station
Roboking 2.0
Remote controller
Side brush
(2 pieces)
OWNER’S MANUAL
CLEANING ROBOT
VR6170LVM
Before using, please carefully read the Safety Precautions pages to
allow for safe operation of the product. After reading the operation
manual, please keep it in an easily accessible location.
www.lg.com
6
PARTS DESCRIPTION - Roboking 2.0
 Figures can be different from actual objects.
Plan view
Manipulation button
Dust bin cover button
Dust bin cover
Status indication lamp
Upper camera sensor
Detecting sensor of home station &
receiving sensor of remote controller
Ultrasonic sensor
Obstacle detecting sensor window
Ventilation port
Cliff detection sensor
Charging terminal
Brush
Side brush
Wheel
Lower camera sensor
Mop plate fixing hook
Battery
Power switch
Front view
Rear view
Bottom view
7
PART DESCRIPTION – HOME STATION / DUST BIN
 Figures can be different from actual objects.
Home station
Dust bin
Remote controller holder
Charging terminal
Reset button
Sponge filter
HEPA filter
Dust bin handle
Dust bin cover
Suction port cover
Dust bin cover
opening button
Power cord fixing hook
8
BUTTON FUNCTIONS – Roboking 2.0
• Use the TIMER button to start cleaning after a set amount of time has elapsed.
• The timer can be set from 1 to maximum of 12 hours in 1 hour units.
• If the timer is set whilst the unit is away from the home station, the cleaning
time will be reduced. Therefore use the product while attached to the home
station as much as possible.
• The timer setting is inoperative if there is no dust bin.
• Press this button to change the cleaning mode.
• When the product is attached to the home station and when the timer is set,
spot cleaning mode cannot be selected.
TIMER
MODE
HOMING
START/STOP
• Press the START/STOP button to turn the Roboking 2.0 on/off or start/stop
cleaning.
• Press the START/STOP button while the Roboking 2.0 is on and it will
automatically start cleaning.
• If the START/STOP button is pressed during automatic cleaning, the Roboking 2.0
will stop cleaning.
• Press and hold the START/STOP button for approximately two seconds to turn
off the Roboking 2.0.
• If the button is pressed while in the timer mode, the reservation will be canceled.
• Press the HOMING button to move the Roboking 2.0 to the home station for
battery charging.
• When cleaning is complete or the battery is low, the device will automatically
move to the home station to charge the battery even without pressing the
HOMING button.
9
BUTTON FUNCTIONS – REMOTE CONTROL
• The Roboking 2.0’s power supply cannot be turned on with the remote control.
• If the main unit is turned off, the remote control will not activate the unit.
• To turn the cleaner on from the stand by mode or off during cleaning, use START/STOP
button on the top of Roboking 2.0.
• In order to do spot cleaning, timer cleaning, zigzag cleaning, and spatial expansion cleaning,
you must first stop the operation of the Roboking 2.0.
Start
The Roboking 2.0 will start
cleaning
Charging
The Roboking 2.0 will move to the
home station for charging.
Timer
The timer can be set from 1-12
hours in the future. (Page 20)
Stop
If the Roboking 2.0 is in operation
it will be stopped.
If it has been set for timer cleaning,
the reservation will be canceled.
Zigzag cleaning
Cleaning will be performed by
the Roboking 2.0 in the zigzag
traveling fashion. (Page 18)
Spot Cleaning
Cleaning will concentrate
within a space of about 1 m
(3.28 ft). (Page 19)
Directional button
The Roboking 2.0 will move
as desired by the user: to
front, rear, left, and right
sides for cleaning.
Cell by Cell cleaning
The Roboking 2.0 will clean
using the spatial expansion
style.
(Page 18)
Tip
10
DISPLAY STATUS INFORMATION
• Once the cleaning mode is selected, it will be kept in memory even when the power is
turned off.
• To cancel the timer setting, press the STOP button on the remote control or the START/
STOP button on the Roboking 2.0.
Zigzag cleaning
• Indicates when the
Roboking 2.0 is in zigzag
cleaning mode. (Page 18)
Timer icon
• This indicates when timer
cleaning has been set up.
(Page 20)
Battery and timer hour
indication
• While waiting for cleaning,
the remaining battery charge
will be shown.
• While waiting for timer
cleaning, the reservation time
will be shown.
• The state of the Roboking 2.0
will be shown. (Page 17)
Spot cleaning
• Indicates when the
Roboking 2.0 is in
spot cleaning mode.
(Page 19)
Spatial expansion
cleaning
• Indicates when the
Roboking 2.0 is in
spatial expansion
cleaning mode.
(Page 18)
Battery icon
• Indicates when the
remaining charge
is displayed on the
battery level indicator,
and flashes when
charging is required.
(Page 17)
Tip
11
BEFORE YOU START
• Do not use this device in a room where a child is left alone. The child could be injured.
• Remove fragile or unnecessary objects from the room to be cleaned.
Especially, remove expensive ceramics and valuables from the floor.
• Close the cover of the dust bin before cleaning.
• Remove any moisture that might be on the floor.
• Remove cables, strips, towels, mat etc. from the floor so they will not get caught by the brush.
• Confirm whether battery charge is sufficient, and if it is low, recharge it.
• Empty the dust bin if it is full.
• Close the doors of any room that you do not want the Roboking 2.0 to enter. During cleaning,
the Roboking 2.0 may enter another room and continue cleaning.
• When the mop is attached, Roboking 2.0 will not be able to go over thresholds of 5mm or higher.
If you are not planning to use the mop for cleaning, separate the mop before using Roboking 2.0.
1. Open the battery cover by lifting the rear hook of the remote controller.
2. Insert two AAA batteries, checking for +, - nodes while loading.
3. Close the battery cover completely so that the batteries will not fall out.
• Only press one button at a time.
• Do not drop or subject it to forceful impact.
• Do not store it near devices that give off heat, fire or hot air.
• Certain fluorescent lamps, such as 3 wavelength fluorescent lamps, can interfere with the activation of the
remote control. Therefore, use it as far away as possible from such lamps.
• If the remote control is far from the Roboking 2.0 when activated, it may fail to operate properly. Use the
device within 3 m (9.84 ft) of the Roboking 2.0 if possible.
Check these items before cleaning
Loading the remote controller battery
Precautions while using the remote control
–
+
+
–
–
+
+
–
–
+
+
–
17
HOW TO CHARGE THE BATTERY
Check 1:
If the battery is not charging even when the Roboking 2.0 is
attached to the home station, check the following items.
- Turn the power switch on the bottom of the Roboking 2.0
off once and then on again.
- Check the power lamp of the home station.
- Wipe the terminal on the home station with a dry cloth
Check 2:
If the battery is still not charging after the previous check,
try the following.
- Manually attach the Roboking 2.0 to the home station.
- Press the reset button at the rear of the home station for
three seconds.
The remaining battery charge can be confirmed from the charge indication light, which will indicate charge
as follows:
• During charging, the charge remaining indication light will icker.
• When charging is completed at the home station, only the battery icon will illuminate to save power.
• The battery icon will icker when battery charging is required.
Full charging
(Under charging)
The status indication lamp
while the robot is charged
(In spatial expand mode)
High Middle Low Charging is
required
※
If there is still an area to be cleaned when the Roboking 2.0
is returned to the home station for charging, the selected
cleaning mode is displayed.
- When the battery is fully charged, it cleans the area that
remains to be cleaned. (Perform 1 time)
- During charging, when the cleaning mode is displayed,
pressing the START button on the remote controller or
the START/STOP button on Roboking 2.0 will cause the
Roboking 2.0 to search for the un-cleaned area and start
cleaning.
- Pressing the mode selection button (ZIGZAG, CELL BY
CELL) will start the cleaning process from the beginning.
Remaining Battery Charge Indicator
If the Battery is Not Charging
Flickering
In the case of not
existing an area to
be cleaned
In the case of
existing an area
to be cleaned
(Flickering)
Charge
terminal
18
CLEANING MODES
With zigzag cleaning, the total of the cleaning area will be
cleaned with the repetition of zigzag traveling.
If rapid cleaning is desired, use zigzag cleaning.
When pressing ‘ZIGZAG’ button on the remote controller,
zigzag cleaning will be started while zigzag cleaning icon is
indicated by the indication lamp.
With spatial expansion cleaning, the cleaning will be
performed by dividing the cleaning area into partial square
spaces.
If elaborate cleaning is desired, use spatial expansion
cleaning.
When pressing ‘Cell by Cell’ button on the remote
controller, spatial expansion cleaning will be started
while spatial expansion cleaning icon is indicated by the
indication lamp.
The 1st stage:
The maximum outline of 3m x 3m of cleaning area
will be cleaned. (The size of outline will be changed in
accordance with the shape of the house inside.)
The 2nd stage:
Inside of the outline will be cleaned with zigzag traveling.
When the 1st, 2nd stages are completed, the inside of
the cleaning area will be cleaned through the repetition of
above cleaning method as the device is being moved to
the next cleaning area.
• Once set up, the cleaning mode will be kept in memory even after the power supply is
turned off.
• During operation, if a mode change is required, press the STOP button and then select the
mode.
Zigzag Cleaning
Spatial Expansion Cleaning
Tip
19
AUXILIARY CLEANING MODES
This method of cleaning involves manually moving the Roboking 2.0 by pressing the directional (arrow)
buttons on the remote control.
The interior space will be cleaned by the Roboking 2.0 as it is being moved to the front, rear, or rotated to
the left and right side according to the input of the directional buttons.
If it meets an obstacle during manual cleaning in a forward motion, it stops.
Use this cleaning method when concentrated cleaning of a small interior space is required.
After moving the Roboking 2.0 to the location to be cleaned, press the SPOT button on the remote control.
The spot cleaning icon will illuminate on the Roboking 2.0, and concentrated cleaning will be performed for
a space within a radius of 1 m (3.28 ft).
※
During charging, the spot cleaning button on the remote control will not activate.
※
The following device show weaker on inhalation
than ordinary vacuum cleaner, but with rotation
brush and side rotation brushes, the device
shows similar performance on cleaning as
ordinary vacuum cleaner.
Manual cleaning
Spot Cleaning
It stops at the started position after
completing the cleaning(takes 4~5 min.).
Brush
Side brush
20
TIMER CLEANING
1. By pressing the TIMER button on the remote
control or the Roboking 2.0, a cleaning time can be
scheduled.
2. Adjust the time as much as desired by multiple
presses of the TIMER button. Each time you
press the button, the time will increase by one
hour.
- The start time can be set up to a maximum of
12 hours and once set up, the time in hours, will
be indicated by the status indication lamps.
3. After setting up the start time, press the START/STOP
button on the Roboking 2.0 or wait about five seconds.
When the timer setting is complete, a melody will sound,
and the timer indicator will remain on.
- If the timer is set, timer icon of a clock shape is
displayed on the status indicator lamp.
Set the timer to schedule the cleaning and begin in 1-12 hours.
The timer setting is inactive if there is no dust bin.
• When the set up time elapses, cleaning will start automatically.
• Use the timer setting when the Roboking 2.0 is attached to the home station. If the timer is
set while Roboking 2.0 is away from the home station, the cleaning time can be shortened.
• To cancel the timer setting during the set up time, press the STOP button on the remote
control or the START/STOP button twice on the Roboking 2.0.
1 hour
9 hours
6 hours
12 hours
Tip
21
MOP CLEANING (OPTION)
1. Attach the ultra microfiber mop to the Velcro
of the mop plate as shown in the figure.
※
To prevent the Roboking 2.0 from
malfunctioning, attach the mop so that the
mop attaching guide will not be covered by
the mop.
2. Accurately match up and insert the mop plate
fixing hook on the lower section of the
Roboking 2.0 into the fixing groove of the
mop plate.
3. When you accurately match up and press the
mop plate to the rear side of the Roboking 2.0,
it will mount with a clicking sound.
※
Be careful to properly mount the mop plate,
or it can separate during cleaning.
For mop cleaning, mount the mop and mop plate to the Roboking 2.0 according to the following instructions:
By attaching the ultra microfiber mop, you can
effectively use the Roboking 2.0 to remove dust
from hard floors.
When the mop plate is attached, the Roboking 2.0
will not climb on to carpets or over thresholds, in
order to prevent transferring dirt from the mop.
• To avoid odors, wash any foreign material or dust off the mop after cleaning is complete.
• To avoid staining floors, do not use the ultra microfiber mop to clean when dirt is mixed with
liquids such as coffee or ink.
• To avoid damage to carpets from the Velcro or dirt transfer from the mop, do not clean the
carpet while the mop plate or mop is attached.
• Keep the ultra microfiber mop dry. Do not use it on wet surfaces.
If there is moisture, it can interfere with the navigation.
Ultra microfiber mop
Mop plate
Mop plate
Fixing hook
Fixing groove
“Click!”
Ultra microfiber mop
Ultra microfiber mopUltra microfiber mop
Mop fixing section With mop attached
Bottom camera sensor
Tip
22
LOCATION SEARCH FUNCTION
When the user removes any abnormal condition of
Roboking 2.0 or moves the location arbitrarily, the
location search function will activate.
1. Locate Roboking 2.0 near the location where
Roboking 2.0 was moved.
※
Location search is more effective when
Roboking 2.0 is closer to the location where it
was moved.
※
If it goes out of diameter of 1m from the
occurrence position, it becomes difficult to
search the position.
2. Press the START/STOP button on Roboking 2.0 or START button on the remote controller.
Roboking 2.0 will start the location search function along with an audio guide.
※
When the location search is successfully completed, Roboking 2.0 will continue to the cleaning from where
it was moved. If position search fails, it will start again from the beginning.
Roboking 2.0 remembers its location while cleaning.
If the user moves the Roboking 2.0 while it is operating, it will search its location with
the location search function so that it can continue from the previous location.
Change location
Location of incident
Location of incident
1m
1m
When the location search
function is activated, the
cleaning mode of the status
indicator will flash
Checking current location.
• When the power is turned off after the location search function is set, the location search
function will be canceled.
• Location search is more effective when Roboking 2.0 is closer to the location where it was
moved.
• The position search function will be cancelled if the remote is pressed to engage any other
function.
Tip
23
CLEANING THE DUST BIN
1. Open the dust bin cover by pressing the PUSH
button on the Roboking 2.0.
2. Grab the handle of the dust bin and pull it
upward.
3. Separate the HEPA filter and the inside sponge
filter by removing the HEPA filter
※
To clean the dust bin filter, refer to page 24.
4. Lift the cover upward while pressing the
separation button on the dust bin.
5. Empty the dust bin and clean it with a cleaning
brush or under running water.
※
Please use vacuum cleaner when cleaning the
filter.
(Be sure to fully dry the filter after washing it. It
may can affect inhalation or can make smell.)
6. After cleaning with water, completely dry the dust
bin in a well-ventilated area out of direct sunlight.
7. When you have completed cleaning the dust bin,
close the dust bin lid and replace the sponge
filter and HEPA filter.
8. Put the dust bin into the Roboking 2.0 and close
the dust bin cover.
If the dust bin is full, suction power can be weakened. Clean the dust bin before and after each cleaning
session. Clean the dust bin using the following sequence:
• After cleaning, always mount the dust bin filters (HEPA filter, sponge filter) to the dust bin.
If they are not mounted, dust may enter the Roboking 2.0 interior and cause product failure.
• After cleaning the dust bin, make sure to start the operation with the dust bin installed.
If operation is attempted without the dust bin, a voice message, “please check the dust bin”
will sound.
Tip
24
CLEANING THE DUST BIN FILTER
The dust bin filters are comprised of the HEPA filter and the sponge filter.
Clean the HEPA filter and the sponge filter according to the following sequence:
1. Separate the HEPA filter and the inside sponge
filter by removing the HEPA filter (as shown).
3. After washing the HEPA filter and the sponge filter
with water, place them out of direct sunlight and allow
them to dry completely.
※
Please use vacuum cleaner when cleaning the filter.
(Be sure to fully dry the filter after washing it. It may
can affect inhalation or can make smell.)
4. Mount the cleaned HEPA filter and sponge filter
into the dust bin according to the sequence
shown to the right. When assembling the filter,
the filter handle should face upward.
2. Carefully clean any fine dust off the HEPA filter and
the sponge filter with a vacuum cleaner or water.
• In order to maintain the performance of the Roboking 2.0, the HEPA filter should be cleaned
with a cleaning brush or vacuum cleaner at least once a week, and should be washed under
running water at least once a month.
Tip
25
CLEANING THE BRUSH
Insert the fixing hook on the
opposite side of the brush
(marked with a rounded
rectangle) by matching it to
the separation groove of the
brush.
Insert the fixing guide in front
of the brush by matching it to
the fixing groove located on the
main unit.
Close the cover by pressing
it down until you hear a click
from the fixing hook.
※
Be careful that the side
brush is not caught by the
cover.
Grab the brush and remove
by pulling it up.
Clean the brush with a vacuum
cleaner, scissors, etc.
Insert the fixing hook on the
side of the brush (marked with
the square) by matching it to
the fixing groove of the brush.
Lay a smooth cloth on the
floor. Turn the Roboking 2.0
over and put the Roboking
2.0 on the cloth. Turn off the
power switch before cleaning.
Separate the cover by pressing
the fixing hook and pulling
upward.
Wearing gloves turn the brush
until the separation groove of
the brush appears.
The brush, located on the bottom of the Roboking 2.0, helps with the suction of foreign objects. Perform
the following steps to clean the brush:
※
Please make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
Separation
groove of
brush
26
CLEANING THE SENSOR/CHARGING TERMINAL
Receiving sensor of
remote controller
Camera sensor
• Do not clean the Roboking 2.0 by directly spraying it with water, thinner, benzene, etc.
• Call the service center if the sensor or charging terminal is damaged. Sensor and terminal
damage can cause the product to malfunction.
There are sensors on the Roboking 2.0 that can detect obstacles, stairways
and the home station for charging the battery. In order to maintain the
performance of the Roboking 2.0, regularly clean the sensors and charging
terminal as follows:
1. Lay a smooth cloth on the floor, overturn the Roboking 2.0 and put it on
the cloth.
※
Please make sure to remove the dust bin before turning over the main body.
Otherwise, the dust in the dust bin may fall out.
2. Turn off the power switch on the bottom of the Roboking 2.0. Injury can
be caused by the activation of the Roboking 2.0 if the main power is not
turned off.
3. Use a smooth cloth or cleaning brush to wipe the dust off each sensor
and the charging terminal as described below.
Charging terminal
Obstacle detection sensor
Cliff detection sensor
Charging terminal
Bottom camera sensor
Lens
Tip
※
The device may move backwards while operating when the cliff sensor or bottom camera sensor is
contaminated.
Please clean the sensor with soft brush or cleaning brush.
27
CLEANING THE SIDE BRUSH
Foreign objects/materials such as hair can easily adhere to the side
brush. Remove such materials at least once a week.
If excessive amounts of foreign materials are stuck to the brush,
there is the risk of damage to the brushes.
If the floor is rough or skirting boards are frequently cleaned, the side brush may bend or become
damaged. In this case, use the following method to straighten the side brush.
1. The following procedure is helpful in restoring
deformed brushes.
2. Turn off the power supply by pressing the
START/STOP button on the Roboking 2.0 for two
seconds.
3. Place the Roboking 2.0 at the end of a table to
make cleaning the side brush easier. Make sure
that the Roboking 2.0 is not in danger of falling.
4. Soak the side brush in warm water.
5. Press down on the side brush for about ten
seconds so that it is completely submerged in
the water.
6. Slowly wipe the side brush by sliding it through
your hand.
7. Rotate the side brush and repeat steps 4-6 for
each section of the brush.
8. Use the side brush only after it has completely
dried.
1. Remove the screw and separate the side brush.
2. Exchange and re-assemble new side brushes.
How to change the side brush
30
TROUBLESHOOTING
When an abnormality is detected with the dust bin, the voice,
“Please check the dust bin”, is announced.
• Is the dust bin tted correctly?
Open the dust bin cover, and if check if the dust bin is actually fitted.
The unit will not operate without the dust bin.
 If the dust bin cover is opened, close the cover before operating the unit.
When remaining amount of battery is almost nil, the voice, “Battery is low”, is generated.
• Initiate battery charging of Roboking 2.0 by moving it to the home station.
If Roboking 2.0 is attached to the docking station, it will start the recharging with the recharging start
melody.
When the voice, “Please check the dust bin”, is announced
When the voice, “Battery is low”, is announced.
33
PRODUCT SPECIFICATIONS
Item/Model LG Roboking 2.0
VR6170LVM
External Dimensions
Φ
360 mm
×
90 mm
Weight 3.2 kg
Power Consumption 18 W
Battery (Fully Charging) DC 16.8 V
Traveling Velocity 350 mm/sec
Use Time Approx. 100 minutes
(Based on general wooden floor)
Charging Time 3 hours
Main Functions Obstacle detection
Fall prevention
Timer cleaning
Error indication
Location search
Automatic / manual charging
Dry mop (Wiping)
Corner cleaning
Voice output
Map building
Spot cleaning
Spatial expansion cleaning
Zigzag cleaning
Item/Model Home Station VR607
External Dimensions 245 mm
×
193 mm
×
132 mm
Rating AC 220-240V,50Hz
Output Voltage/Current 17.1VDC / 1.1 A
Power Consumption 23 W
Item/Model Battery
Type Lithium Ion Polymer Battery
MEMO
MEMO
Made in Korea
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LG VR6170LVM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LG VR6170LVM in the language / languages: English as an attachment in your email.

The manual is 23,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of LG VR6170LVM

LG VR6170LVM User Manual - English - 39 pages

LG VR6170LVM User Manual - German - 40 pages

LG VR6170LVM User Manual - German, French, Italian - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info