688101
63
Zoom out
Zoom in
Previous page
1/84
Next page
125
INSTALLER SETTING
124
INSTALLER SETTING
ENGLISH
Installer setting - ventilator
• You can set the product user functions.
• Some functions may not be displayed/operated in some product types.
Menu Applied products Description
Test run setting DX(Direct Exchanger) Type It is the function to set the trial operation at the initial product installation.
Central control address Setting General
It is the function to set the central control address of the indoor unit during
the central controller connection.
Air supply ESP
General/DX Type
It is the function to set the fan speed value corresponding to the air supply
side fan speed.
Air discharge ESP
It is the function to set the fan speed value corresponding to the air dis-
charge side fan speed.
Temperature sensor setting DX Type
It is the function to select the temperature sensor that will decide the indoor
temperature.
Product direction General It is the function to set the ventilation indoor unit’s installation direction.
Express ventilation priority
General/DX Type
It is the function to set the priority of the air supply and discharge during the
express ventilation operation.
RMC master/slave setting It is the function to set group control or 2-remote controller control.
Override master/slave setting DX Type
The operation master / slave selection function is to avoid other mode oper-
ations, and it is the function to prevent the selection of the opposite mode
of the indoor unit set as master by the indoor units set as slaves.
Dry contact mode setting DX Type
Dry contact function is the function that can be used only when the dry con-
tact devices is separately purchased and installed.
Fixed fan speed setting DX Type
It is the function to set the indoor unit’s fan speed option to variable or fixed.
Hum. Of Stand-alone Vent.
Mode
General/DX Type
It is the function to set whether to use the humidification function in the di-
rect cooling type ventilation’s ventilation single operation.
Hum. Of Vent. With Heating
Oper.
DX Type
It is the function to set the direct cooling type ventilation’s heating humidifi-
cation function as auto or manual.
Vent. Fan Speed Alignment General
It is the function to increase/decrease ventilation’s standard fan speed from
the current status according to the field environment.
Indoor unit address verification DX Type
This function allows you to check the address of the indoor unit designated
by the outdoor unit.
Indoor unit Auto-Start setting DX Type
It is a function that sets whether to restore the indoor unit operation by re-
suming the previous power-on state or as power-off state in the power fail-
ure compensation.
CN_EXT setting DX Type
It is the function to set the indoor unit’s Dry Contact Port to control external input
and output according to DI/DO set by the customer. (It is the function to decide the
usage of the contact point port (CN_EXT) mounted in the indoor unit PCB.)
ODU function master setting DX Type It is the function to set the outdoor unit’s function Master / Slave.
Low noise mode priority setting DX Type
It is the function to set the main agent of the low noise mode control. (It is
the function to set only one of the outdoor unit / remote controller can con-
trol the low noise operation.)
Filter check alarm General This function sets the filter check alarm of the ventilation product.
Test run setting (air conditioner / DX ventilator)
After product installation, the Test run must be performed. For Test run related details, refer to
the product manual.
• In the installer setting list, select the Test run setting category, and press [OK] button to move
to the detail screen.
- You can select ‘cooling Test run / heating Test run’
- During the Test run, if you start the following functions, the Test run stops.
Operation mode, desired temperature, fan speed, wind direction, start/stop
OK
1,MFL69312302,영영 2018. 11. 19. 영영 11:19 Page 124
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LG CREMTB100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LG CREMTB100 in the language / languages: English as an attachment in your email.

The manual is 16,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of LG CREMTB100

LG CREMTB100 User Manual - German - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info