691798
193
Zoom out
Zoom in
Previous page
1/204
Next page
This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom
customers.
This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for
which it is designed. Telecom will accept no responsibility should diculties arise in such circumstances.
The decadic (or pulse) dialing on this device is unsuitable for use on the Telecom network in New Zealand.
For correct operation, the total of all the Ringer Equivalence Numbers (RENs) of all parallel devices connected
to the same telephone line may not exceed 5. The REN of this device is located on the label.
This device uses an RJ-11C modular connector. Contact your point of purchase if a BT adapter is required. The
Lexmark part number is 80D1873.
Some parameters required for compliance with Telecom's telepermit requirements are dependent on the
equipment associated with this device. The associated equipment shall be set to operate within the following
limits for compliance to Telecom's specifications:
There shall be no more than 10 call attempts to the same number within any 30 minute period for any single
manual call initiation, and
The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt
and the beginning of the next call attempt.
The equipment shall be set to ensure that automatic calls to
dierent
numbers are spaced such that there
is not less than 5 seconds between the end of one call attempt and the beginning of another.
Japanese telecom notice
The installed optional modem is in compliance with Japanese Telecommunication Law and has been Certified
by JATE, with the following Certification Number:
A18-0046001
Lexmark International, Inc.
LEX-M14-002
A18-0046001
Using this product in Switzerland
This product requires a Swiss billing tone filter (Lexmark part number 80D1877) to be installed on any line which
receives metering pulses in Switzerland.
Utilisation de ce produit en Suisse
Cet appareil nécessite l’utilisation d’un filtre de tonalité de facturation suisse (nº de référence Lexmark :
80D1877) devant être installé sur toute ligne recevant des impulsions de comptage en Suisse.
Notices 193
193


Need help? Post your question in this forum.

Forumrules
1

Forum

lexmark-mc3224

Reset search

  • how do i change the language from manderin to english
    Submitted on 17-8-2022 at 17:32

    Reply Report abuse
  • I have an MC3224 printer attached to a DELL laptop with Windows 10 installed. I'm trying to set up to scan to the computer. All I can find is that I need an IP # for the printer, which I do not have or at least cannot find. What can I do to make this thing operate ? Submitted on 25-5-2022 at 00:33

    Reply Report abuse
  • How do I disable the power saver setting to prevent hibernation?
    Submitted on 24-1-2022 at 19:13

    Reply Report abuse
  • My MC3224 displays a paper jam fault. There is no jam, but the printer will not reset the fault. Nothing I have done helps. Is there a way to reset the fault? Submitted on 14-10-2021 at 14:15

    Reply Report abuse
  • Can you go back and open the setup wizard to make changes? Submitted on 10-4-2021 at 02:02

    Reply Report abuse
  • can you go back and access set up wizard to make changes Submitted on 10-4-2021 at 02:01

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lexmark MC3224 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lexmark MC3224 in the language / languages: English as an attachment in your email.

The manual is 12,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Lexmark MC3224

Lexmark MC3224 User Manual - German - 201 pages

Lexmark MC3224 User Manual - Dutch - 197 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info