765518
46
Zoom out
Zoom in
Previous page
1/80
Next page
44
protected from frost.
No metal parts may enter the shaft to slide the battery
(risk of short circuit). Never use the charger in moist or
wet conditions. Suitable for indoor areas only. Make sure
the system voltage corresponds to the charger type plate
details. There is a risk of electric shock.
Cable connections to be separated by pulling the plug
only. Pulling the cable could damage both the cable
and plug. As a result, electric safety would no longer be
guaranteed.
Never use the charger when the cable, plug or the
machine is damaged by external influences. The
accumulator must be packaged (plastic bag, box) or
accumulator contacts must be sealed up for accumulator
disposal, transport or storage. Make sure the cooling
function is not limited by covering the cooling slots. Do not
operate the appliance near heat sources or on a flammable
surface.
Never open the charger.Contact a specialised workshop
in case of any defect.
The outer battery surface must be clean and dry before the
battery starts being charged.
Chargers are exclusively suitable to charge these
replaceable batteries:
Typ LI 22 / BT20 20V & Typ LI 22-2 / LBB25R
Charging any other battery is not allowed.
MAINTENANCE
DANGER
Remove the battery pack before starting any
adjustment, cleaning and maintenance work
on the device.
Wait until all rotating parts have stopped
and the appliance has cooled down.
Keep the device, in particular the air vents, clean at all
times. Never spray water on the device body! Never
clean the machine and its components with solvents,
flammable or toxic liquids. Us only a damp cloth making.
Use only original accessories and original spare parts.
Using other spare parts can result in accidents/injuries of
the user. The manufacturer will not be liable for any such
damage.
Please contact our service department if you need
accessories or spare parts.
Only a regularly maintained and treated appliance can
serve as a satisfactory aid. Insufficient maintenance and
care can lead to unforeseen accidents and injuries.
Repairs and works specified in these Instructions may
only be performed by qualified authorised staff.
Keep your chain saw professionally maintained and safe.
• Sharpening the chain safely is a skilled task. Therefore,
the manufacturer strongly recommends that a worn or
dull chain is replaced with a new one, available at your
service agent. The part number is available in the product
specification table in this manual.
Follow instructions for lubricating and chain tension
checking and adjustment.
After each use, clean the machine with a soft dry cloth.
Remove any chips, dirt and debris in the battery bay.
Check all nuts, bolts, and screws at frequent intervals
for security to ensure the machine is in safe working
condition. Any part that is damaged should be properly
repaired or replaced by a service station.
Replacing the guide bar and saw chain
WARNING
Wear protective gloves.
A dull or improperly sharpened chain can cause
excessive motor speed during cutting which may
result in severe motor damage.
Failure to replace or repair a damaged chain can
cause serious injury.
The saw chain is sharp. Always wear protective
gloves when performing maintenance to the chain.
Inspecting and cleaning the chain
brake
Always keep the chain brake mechanism clean by lightly
brushing the linkage free from dirt.
Always test the chain brake performance after cleaning.
Refer to “Checking and operating the chain brake”
section in this manual for additional information.
Maintenance schedule
Daily check
Bar lubrication Before each use
Chain tension Before each use and
frequently
Chain sharpness Before each use, visual
check
For damaged parts Before each use
For loose fasteners Before each use
Chain brake function Before each use Inspect
and clean
Guide Bar Before each use
Complete saw After each use
Replacement parts
Chain 90PX052X
Guide Bar 144MLEA041
Chain must be fitted with bar from the same
manufacturer according to above combinations.
EN
ENGLISH
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Levita CS35 2x20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Levita CS35 2x20V in the language / languages: English, German as an attachment in your email.

The manual is 10,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info