611570

Lenovo px12-450r - LifeLine 4.1 Manual

156
Zoom out
Zoom in
Previous page
1/167
Next page
Configuring Port Forwarding on Double NAT Networks
If for some reason the network configuration cannot be changed and your setup requires the double NAT,
you must perform the port forwarding steps twice. On the primary router, set the port forwarding to the
cascaded router's external IP address. On the cascaded router, set the port forwarding to the px12-450r's
IP address.
Bridging the Secondary Router
Make sure that the primary router (usually the one connected to or acting as the DSL/Cable modem) is the
only one with DHCP (Dynamic Host Configuration Protocol) and NAT (Network Address Translation)
enabled. The secondary should be changed to bridging mode. Ensure that the secondary router connects
to the primary router using a standard port rather than the port labeled Uplink or internet. This turns your
secondary router into a switch; however, you can still enable its Wireless Access Point if so equipped.
Refer to the documentation that came with your router for configuration information and settings.
Bridging the Primary Router
If none of the above options are available, you must enable transparent bridging on your primary router.
This may require contacting your ISP (Internet Service Provider) to configure the DSL or Cable
Modem/NAT into bridge mode, which then disables the first NAT/Firewall. After this first firewall in the
modem is disabled, the secondary router handles all the network traffic, Port Forwarding, and allows
Remote Access to work.
You should not attempt bridging without help from the ISP. If bridge mode is attempted by the
customer and not configured properly, it can render the customer's internet connection inoperable.
Primary router bridging may also require special configuration information and settings on the
secondary router.
If you configured your px12-450r using DHCP, you may not be able to reconnect to it via Remote Access
after a reboot. DHCP automatically receives an IP address from the server whenever the px12-450r
restarts. This is a very simple way to configure the px12-450r but can cause problems with your router's
port forwarding settings. The router does not dynamically update port forwarding settings and cannot port
forward to your px12-450r if its IP address changes.
To resolve this problem, try one of the following processes:
● Increase the length of the DHCP lease: Your router attempts to remember all DHCP clients and
assigns them the same IP address every time they request an IP address; however, the router
forgets clients if they do not request an IP address for a certain amount of time. Your router has a
setting for the duration of the validity of the DHCP lease. If your network requires DHCP, this
may be a good solution; however, it is not always guaranteed to work. Occasionally updating your
router's port forwarding settings may be required.
● Use Static DHCP: Some routers allow you to assign Static IP addresses through the DHCP
system based on the MAC address of the device. This ensures that the px12-450r always gets
the same IP address, and your port forwarding settings are always correct. Static DHCP allows
you to leave your px12-450r in DHCP mode. Refer to your router's documentation for more
information on configuring DHCP settings.
● Use a Manual IP Address: Changing the Manual IP address reduces the reliance of your px12-
450r on the DHCP server; however, you must perform additional configuration for it to work
properly.
Hardware Management
146 Troubleshooting Routers
… 156 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lenovo px12-450r - LifeLine 4.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lenovo px12-450r - LifeLine 4.1 in the language / languages: English as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Lenovo px12-450r - LifeLine 4.1

Lenovo px12-450r - LifeLine 4.1 User Manual - German - 177 pages

Lenovo px12-450r - LifeLine 4.1 User Manual - Dutch - 176 pages

Lenovo px12-450r - LifeLine 4.1 User Manual - French - 178 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info