792979

Lenco SCD-6800 Manual

10
Zoom out
Zoom in
Previous page
1/56
Next page
10
Version: 2.0
➢ Press “ Stop ” button twice (10) at CD stop mode to cancel all programmed memory until the “Prog” indicator disappear on
LCD display (8).
➢ For MP3 disc/file, press the “Folder up” button (20) to select the 1st track of next folder directly and hence to speed up the
song selection.
➢ The programming mode will automatically stop if no button is being pressed in a period of about 30 seconds after pressing
the Memory button (12).
Remark:-
MP3 track format requirement:-
- Bit rate: 32 kbps~320kbps, sampling rate: 32kHz, 44.1kHz and 48 kHz decodable
- The performance of playing MP3 disc is various from the quality of recording disc and the method of recording.
Furthermore, the searching lead-time for MP3-CD is longer than normal CD due to difference format.
Playback of MP3 song via USB storage media
Connecting
The system is able to decode and playback all MP3 file which stored in the memory media with USB connecting port.
1. Set the system at Standby mode first or other function except USB mode.
2. Plug-in the USB pen-drive with the face up & make sure it going into completely.
⚫ Connecting the USB upside down or backwards could damage the audio system or the storage media (USB thumb driver).
Check to be sure the direction is correct before connection.
3. Turn on the unit again by On/off button (17) and set press Function button (9) to select USB mode. The system will start
reading the storage media automatically after connecting, and LCD display (8) will show the total number of MP3 files being
detected.
4. Repeat the same playback procedure as playing CD/MP3 disc as above.
Remark
- The system can detect and read the file under MP3 format only at USB mode but not other music file format.
- If connect the system to MP3 player via the USB socket, due to variances in file system format, some MP3 player may not
be able to play via the USB socket. This is not a malfunction of the system.
- USB port does not support connection with USB extension cable and is not designed for communication with computer
directly
- Due to ErP stage two requirement and protect the environment (for European market only). The unit will switch to
standby mode automatically once no any music playing over 15 minutes.
Removing of USB
To remove the USB turn off the power or switch the function mode to either cd or tuner mode first. For USB port – un-plug it by
pulling out the USB socket directly
Listening to tape
General operation
Stop/eject key
press to stop all deck operation. Press again to open the cassette door.
Fast forward key &
Fast rewind key
press to start rapid tape winding in either forward or reverse direction. Press stop/eject key, the
cassette spools stop turning.
Play key
press to start playing tape.
Pause key
press to stop tape operation temporarily. Press again to resume play.
Playback
⚫ Select “Tape” by Function button (9)
⚫ Put in the cassette tape.
⚫ Press play key to active playback
⚫ Adjust the Volume up/down control (14) to the desired level.
⚫ Use pause key when you want to stop playback temporarily.
⚫ Press stop/eject key when finished.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lenco SCD-6800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lenco SCD-6800 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info