601868

Lenco SCD-1900 Manual

9
Zoom out
Zoom in
Previous page
1/60
Next page
EN-8
4. Pair and connect to Lenco BOOST-8/Lenco SCD-1900/Lenco CAJUN-8/Lenco SCD-1500 BT on the
audio source device. If prompted for passcode, enter “0000”.
5. When pairing is successful, “CONNECT” shows on the display, and it is ready to stream music. Press
the PLAY/PAUSE button if the playback does not start automatically, or operate the audio source
device to start playback.
6. During playback, press the PLAY/PAUSE button to cease or resume the playback.
7. During playback, use the NEXT or PREVIOUS button to skip to the next/previous tracks.
NOTE: The above steps for Bluetooth connection and playback are intended for reference purpose only.
Please refer to the instruction manual of the Bluetooth audio source device for more details.
DISCONNECTION/RECONNECTION TO THE BLUETOOTH AUDIO SOURCE
Press the STANDBY button to turn off the unit, and to disconnect the Bluetooth device.
Turn on the unit and switch to BT mode to automatically retrieve the last paired Bluetooth device.
NOTE:
When the external Bluetooth source device is moved out of the Bluetooth receiving range of the unit,
the Bluetooth connection will be disconnected. Moving again into the receiving range will resume
connection and restart playback through the unit automatically. If the connection does not resume
automatically, please operate as above to reconnect and start playback.
Simultaneous connection of two external Bluetooth audio devices to the unit is not supported. First
disconnect the current Bluetooth connection, then press and hold the PLAY/PAUSE/BLUETOOTH
PAIR button to launch a new pairing, operate another audio source device to make Bluetooth
connection with the unit and start playback.
NFC (Near Field Communication)
This unit has NFC function, which allows an NFC-enabled Bluetooth audio source device to rapidly
connect with the unit and play the audio signal through the unit. Operate as below:
1. Turn the unit on. Activate the NFC function of a Bluetooth audio source device such as a
smartphone.
2. Hold the audio source device close to the NFC scanning area of the unit (in a range within 10cm).
The audio source device will pair and connect with the unit instantly. If the unit is in other modes, it
will be switched to Bluetooth mode automatically.
3. Operate the audio source device to select your desired music to play through the unit. Please refer to
the instruction manual of your NFC audio source device for more details.
USB CHARGING PORT
The USB charging port on the back of the unit acts as a 5V/1A power supply for the purpose of charging
an external USB device such as a smartphone via the device’s original USB charging cable.
NOTE:
1. As long as the unit is connected to AC main supply, the charging function is available any time no
matter unit is at power on or standby mode.
2. When unit is under DC operation, the charging function only available at unit powered up for
emergency use while the charging function is blocked whenever unit is switched to standby mode in
order to save battery power.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lenco SCD-1900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lenco SCD-1900 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 5,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info