792703

Lenco LS-101 Manual

7
Zoom out
Zoom in
Previous page
1/85
Next page
6
SET UP
An AC/DC adaptor with an output of 12V DC 2.0A is included with this Turntable with Bluetooth reception and
Wooden Speakers. The adaptor is required for operating the unit.
Connect the speaker cables from each speaker to the back of the unit
Note: The external speaker cables are color coded, the cable with the red connector should be put in the red
hole and the white one in the white hole.
Firmly and securely insert the DC plug of the adaptor to the DC IN Jack on the back of the unit.
Plug the adaptor’s AC plugs into a power outlet rated at 220-240V AV ~ 50 Hz.
Turn on the unit by the POWER/VOLUME Knob. The Power/Function Led Light Indicator will turn on.
Remark: To avoid Larsen effect or Feedback noise, you can do the following:
1. Put your speakers at minimum distance of 60 cm or more from your turntable
2. Keep the dustcover open when you play a record at higher sound volume
Power On and Mode selection
Turn on the unit by the POWER/VOLUME Knob. You will hear a click sound and the Power/Function Led Light
Indicator will turn on confirming the power is ON. When the power is ON, you can rotate the control normally
to adjust the volume of the music playing.
Rotate the FUNCTION SELECTOR to difference modes ( OUT/PHONO/AUX/ IN).
2. Listen to a Record
1. Raise the dust cover
2. Turn on the unit by the POWER/VOLUME Knob. The Power/Function Led
Light Indicator will light in RED at PHONO mode.
3. Or you can rotate FUNCTION SELECTOR to PHONO mode.
4. Place a record on the turntable platter and set the player speed to match
the record speed.
Note: When playing a single (a 45 rpm record) and/or records with large
centre holes, use the 45 rpm adaptor.
5. Remove the needle cartridge protective cover
Unlock the tone arm lock from the tone arm rest. Push the lift lever backward, the tone arm will gently rise up.
Gently move the tone arm to the desired position over the record and the turntable platter will begin to rotate
when the arm is moved towards it If Auto Stop Control Switch in ON. Release the tone arm onto the turntable
by pushing the lift lever forward and the vinyl record will begin to play.
If the Auto Control Switch is turned ON, the record will stop automatically when finished. If Auto Stop Control
Switch is turned OFF, the record will NOT stop automatically when finished; you must push the lift lever
backward to raise the tone arm and place it back in the rest and then turn off the power to stop the turntable
from spinning.
Remark: AUTO STOP function applies to most 33RPM vinyl records. However, for very few vinyl records, it will
stop when it does not come to the end, or it will not stop when it comes to the end when AUTO STOP is ON.
NOTE: If your record stops before the last track finishes, set the AUTO STOP switch to OFF. Your record will now
play to the end, but you will have to stop the turntable rotation manually.
NOTE: Depending on the record length, AUTO STOP may be enabled before the end of the recording.
Do not rely on AUTO STOP alone to turn off playback.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lenco LS-101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lenco LS-101 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info