793288
161
Zoom out
Zoom in
Previous page
1/163
Next page
159
SOLUCIÓN DE PROBLEMAS
Consulte la tabla que aparece a continuación en primer lugar antes de ponerse
en contacto con nuestro servicio de atención al cliente.
No se proyecta ninguna
imagen o aparece un
mensaje «No Signal» (Sin
Señal)
1. La luz de encendido está encendida. Si no es
encendida, compruebe que el proyector es
enchufado a la red eléctrica, que la toma esté
encendida, y a continuación pulse el botón de
encendido en el proyector.
2. No olvide quitar la tapa de la lente.
3. Compruebe que los cables estén bien conectados e
instalados según el Manual del usuario.
4. Es posible que la fuente de la imagen no esté
establecida correctamente. Pulse el botón Source
en el Panel de control o en el mando a distancia
para seleccionar el ajuste correcto.
5. Verifique en la sección de Menú bajo Señal de
entrada de vídeo para comprobar que se haya
establecido correctamente.
La Lámpara (Bombilla) se
apaga cuando transcurre un
período de tiempo
¿Está rojo el indicador luminoso de advertencia? Si
ese es el caso, el proyector se sobrecalienta, lo que
apaga la luz de forma automática.
1. Deje que se enfríe el proyector durante un
momento.
2. Cuando se haya enfriado, compruebe que nada
bloquee las rejillas de ventilación.
3. Compruebe que el filtro de aire esté limpio y
límpielo si es necesario.
4. Encienda el proyector.
Si el problema continúa, póngase en contacto con su
proveedor de asistencia para obtener más ayuda.
La imagen es más ancha
en la parte superior/inferior
de la pantalla
Esto se denomina keystone y se debe a que el ángulo
de proyección no es perpendicular a la pantalla. Para
corregir, utilice los proyectores incorporados en la
función Keystone para ajustar la imagen.
Manchas en la pantalla
Uso de una aspiradora para limpiar la lente. Si la
limpieza no soluciona los problemas, póngase en
contacto con su proveedor de asistencia para obtener
más ayuda.
El brillo de la imagen se ha
desvanecido
Esto podría ser debido a la luz ambiental en la
habitación. Si no es así, lo más probable es que
necesite reemplazar la lámpara (bombilla).
161


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lenco LPJ-500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lenco LPJ-500 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info