110590
6
Zoom out
Zoom in
Previous page
1/7
Next page
10
The Sleep timer allows you to set the unit that automatically turn off the Radio
after a selected sleep time.
- To activate the sleep timer and select the sleep time, press the SLEEP
button repeatedly. The sleep time available for choosing are:15, 30, 45,
60, 75 and 90 minutes. The display will show the indicator "SLEEP".
- To switch off the sleep timer, press SLEEP button repeatedly until the
"SLEEP" indicator disappears.
- To switch off the unit before the selected time, press the POWER button
once.
Sleep Timer
11
RESET
RESET button
Care and Maintenance
Do not subject the unit to excessive force, shock, dust or extreme temperature.
Do not tamper with the unit's internal components.
Clean your unit with a damp (never wet) cloth. Solvent or detergent should
never be used.
Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
Keep your unit away from heating appliances and sources of electrical noise
such as fluorescent lamps or motors.
Resetting the Unit
If the unit is subjected to a severe power surge or electric shock, it is possible
that the internal microcontroller may “lock up” and the unit will not respond to
any commands from the top panel controls.
1. In this event, unplug and then reconnect the AC power plug into the wall
outlet.
2. Use a straightened paper clip, toothpick, or similar blunt object to press the
RESET button located at bottom of the main unit (see figure below). The
reset operation clears the system memory and all of your previous settings
will be erased.
Caution: DO NOT use a sharp, pointed object to press the RESET button.
It may damage the reset switch inside the unit.
Rainbow Light Lampshade
The unit has a special feature that its lampshade with rainbow light.
you may activate the rainbow light by sliding the RAINBOW LIGHT switch
to LO or HI position.
EngEng
To enable / disable alarm function
8. To enable alarm function, press the AL1 (AL2) button and the alarm
indicator AL1 (AL2) and light effect indicator (if selected) display.
To disable alarm function, press the AL1 (AL2) button until both the alarm
AL1 (AL2) and light effect indicators are OFF from the display.
Wake to Buzzer (the ALARM SOURCE switch is set to BUZZER position)
When the alarm time is reached, the Buzzer will sound for 3 minutes then
enter auto-snooze mode.
Wake to Radio (the ALARM SOURCE switch is set to RADIO position)
When the alarm time is reached , the alarm will wake up to the tuned radio
station and play for 30 minutes.
Wake to Melody (the ALARM SOURCE switch is set to MELODY position)
When the alarm time is reached , the selected melody (sound effect) will
sound for 30 minutes.
When the alarm sounds, the" rainbow colour" or the "sunlight" light up the
lampshade, if alarm light effect was previously set.
Note : If "sunlight" is selected, the sunlight turns on (max. 30 minutes)
before the set alarm time.
You may activate the snooze function manually after the alarm sounds by
pressing the SNOOZE button. The snooze time is approximately 10 minutes.
The snooze operation can be repeated 3 times.
After the alarm sounds, you may also slide the ALARM SOURCE switch ,
press any button (except the SNOOZE button) on the lampshade , press
BAND button or POWER button to stop the alarm immediately. It will reset
itself for the following day.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lenco CRW-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lenco CRW-2 in the language / languages: English as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Lenco CRW-2

Lenco CRW-2 User Manual - German - 12 pages

Lenco CRW-2 User Manual - Dutch - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info