English
COMPONENTI:
1 – Beans hopper 5 – Support for the positioning of the filterholder
2 – Grinding knob 6 – ON/OFF switch
3 – Programming switch 7 – Pilot lamp : grinder is on/programming
4 – Grinding switch 8 – Socket for power cord
USER INSTRUCTIONS:
Remove the grinder from its box and make sure that all packing parts have been taken off (including the
protection bags).
Lay the grinder on a flat surface to grant an optimal steadiness.
Before using the machine please check:
that the voltage corresponds to the voltage required as stated on the technical data label, on the bottom of
the appliance.
that the power cord has been plugged in the grinder’s socket (8) and in the wall socket and that the switch
(6) is on. The confirmation that the switch is on is that the blue pilot lamp (7) is on.
that the beans hopper (1) contains coffee beans.
Starting the machine:
Before switching the grinder on, make sure that the hopper is covered with the relative lid. Press the grinding
switch (4) with the filterholder in order to start the grinding and obtain the freshly ground coffee directly in the
filterholder. Release the switch and verify the grinding and the quantity of the ground coffee. During this phase the
pilot lamp (7) is on.
Regulation of the micrometric grinding:
Rotate the grinding knob (2) to change the granulometry of the beans. Micrometric regulation does not require any
blockage. Regulate the grinding with the grinder on if you have beans in the mills, with the grinder off if there are
no beans. To regulate the grinding, rotate the grinding knob slightly (2) clockwise (to the right) to obtain a fine
grinding, anti-clockwise (to the left) to obtain a gross grinding.
Regulation of the ground coffee dose:
1. The grinder has an electronic programmable card, where you can program the grinding time for one dose.
The grinding time can vary from 2 seconds to 20 seconds. To set the grinding dose, press the switch (3)
for at least 2 seconds.
2. The pilot lamp (7) goes off because you are in the programming phase.
3. If you want to increase the grinding time, press the switch (3), each time you press it, you add half second
to the time and the pilot lamp (7) blinks one time each half second that you have added.
4. If you want to diminish the grinding time, once you are in the programming phase, keep the switch (3)
ALWAYS pressed and, after 2 seconds, the pilot lamp (7) will blink once for every half second you are
diminishing. Once you’ve diminished the time you wanted, release the switch.
5. To exit from the programming modality, wait 5 seconds or, if you want to grind your coffee immediately,
press the grinding switch (4). After 5 seconds the pilot lamp will blink showing you the seconds that have
been set: one standard blink for each second and two quick blinks for each half second.
How to set the single /double dose:
If you set the time to get 7g (what we advise for 1 dose), wait till the grinder has finished grinding and press the
switch (4) another time to get the double dose (14 g).
Memory of the grinding time:
If, during grinding, you release the switch (4) before the grinding is over (to adjust the coffee in the portafilter or
by mistake), the grinder keeps in memory the remaining grinding time for three seconds. The pilot lamp (7) blinks
to warn you that the set dose has not been totally released. Within three seconds, if you press the switch (4)
again, the grinder will finish grinding the set dose. If you do not press it within three seconds, the grinder will not
keep the remaining time in memory and the next time you press the switch (4), it will grind the set dose from the
start.
Reset the set factory values:
With the grinder off, keep pressed the switches (3) and (4) contemporarily and then switch it on by pressing the switch
(6). The pilot lamp (7) will confirm the reset blinking quickly. Release the switches (3) and (4). With the switch (6) turn
the grinder off and then on again. The set factory values are 6 seconds for 1 dose and 10 seconds for 2 doses.
Routine maintenance and precautions:
- The grinding degree is the most important thing in order to obtain a creamy coffee. This degree changes
according to the coffee blend.
- Please replace, once worn out, the conical mills.
- In order to change the conic mills, please contact an authorised service center.
