622413

LD Systems RoadBoy 6.5 Manual

15
Zoom out
Zoom in
Previous page
1/122
Next page
15
ITALIANOPOLSKIESPAÑOL
FRANCAISFRANCAIS FRANCAISFRANCAIS
FRANCAISDEUTSCHENGLISH
SYSTEM SettInGS AnD oPeRAtIonS:
USING THE WIRED MICROPHONE INPUT
Plug the 6.3 mm Jack connector of your microphone cable into the MIC Jack input. You will find this input on the
back panel of your Roadboy. Make sure that the other end of your cable is correctly connected to the microphone.
If your microphone features an ON / OFF switch, please set it to the ON position. Now use the MIC gain knob to set
the balance between the MIC and LINE inputs. Too much MIC level can cause distortion (Overdrive).
USING WIRELESS MODULE
Start by setting the MASTER level knob of your Roadboy on the zero position. Then turn the POWER-VOL knob of
the wireless module to twelve o’clock position. Now you can synchronize the transmitter (handheld mic or Belt
Pack) with the integrated receiver thanks to the ASC function: Press the ASC button of the wireless receiver modu-
le, the ASC LED now flashes red.
If you are using a handheld transmitter: The Infrared sensor (IR) is placed in the battery compartment under
the capsule. Hold it close to the IR sensor of the wireless receiver module.
If you are using a Belt Pack transmitter: You need to activate the ASC function on the Belt Pack also. Then
hold the Infrared sensor (IR on the rear side) of the belt pack transmitter close to the IR window of the wireless
receiver module. The synchronization lasts a few seconds. If you have installed a second wireless module (opti-
onal), make sure that you are not running both modules on the same frequency in order to avoid any interference
(see frequency list). A flashing RF light shows that your system is functioning and that the synchronization was
successful. You can now increase the MASTER volume of your Roadboy to the desired volume.
Maximum distance between the wireless microphone (or Belt Pack transmitter) and the receiver module is around
60 m in an open space.
USING THE „EXT. SPEAKER“ OUTPUT
Use a speaker cable with 6.3 mm Jack connector to connect the external loudspeaker. Use a speaker with impe-
dance between 4 and 8 Ohm with a minimal power output of 25 W.
CHARGING ROADBOY
Plug the power supply (16 V / 3 A) which is included with your Roadboy to operate your system without batteries
or in order to charge the batteries. The charging time is 8 hours. The charging procedure stops automatically when
the battery is fully charged. You can also keep the Roadboy connected to the AC current and operate it as long as
you wish.
IMPORTANT!
When connecting the battery for the first time or when replacing the battery you MUST mind the
polarity! Red = + (plus) // Black = - (minus).
When the Roadboy is charged for the first time, charging time should be 15 hours. This increases both
battery life and capacity. This procedure should be repeated every 2-3 months. Before this charging
procedure the battery should be empty.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LD Systems RoadBoy 6.5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LD Systems RoadBoy 6.5 in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 8,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info